Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hello,
I am using nrf52832 with PCA10040 and SDK15.1 along with a temperature sensor MAX30205. So far I can write, but I am realizing that I cannot read the second byte...
Hi, I'm using the nRF52840 SDK15.2.0 I'd like to get data from a digital microphone via a PDM interface. The teansfer data to speaker via a I2S interface.
Here is my problem...
I use the SES ver 4.12 with embOS of Segger.
It happened to me all the time.
I take an example from Nordic. I rebuild it with no warning. Then I take and add my files...
During the firmware running, there will be a HardFault_Handler error occasionally.
Is there any way to locate the error source?
Is there any good way to catch the hardware...
Hello. I have a problem with enabling nrfx module. I get this error during prohect compilation: 'NRFX_TWI0_INST_IDX' undeclared here (not in a function); did you mean 'NRFX_TWI_INSTANCE...
Hi,
I'd like to set 3 nrf52840-DK in the following way :
One device acts as central
2 devices acts as peripheral
I'd like the central to be connected to both peripherals...
I have custom board with nrf 52832. I am using SDK 12.3.0. and soft devices s132 V3.0.0 to transmit advertising packets with advertising interval 1s. I have written simple...
I already have a few devices in the field, and I'm curious if it is possible to occasionally update the signing key (e.g. to upgrade key, or compromised key, etc). If not...
Hello, I want to establish a connection between NRF52832 IC and ESP32 Module.
I implemented BLE on ESP 32 and achieved communication between Nordic Mobile app and ESP32...
Hi,
I am trying to used the WINC1500 Wifi module with the nRF9160 DK but I am not getting any data back from the module.
I am using the module
https://www.microchip...
Dear Nordic Support,
I follow this SAADC example to calibrate the SAADC every SAADC_CALIBRATION_INTERVAL.
However, whenever the function nrfx_saadc_abort() is called...
I am running into a strange issue. I want the bootloader to start automatically when I power on the device and then start the application if there is no activity after 30...
Hi,
If I want compiler my project at specified locate, the only thing tat I need to do is following image? Is it right?
After I program this program into address 0x0001D000...
I am trying to make PN7150 work with nRF52840 using TWI Communication.
Problem : PN7150 gets detected with I2C scanner example when using Adafruit Bootloader and programmed...
When I run "pc-ble-driver-py/pc_ble_driver_py/examples/serial_port_enum.py" on armv5tejl GNU/Linux 4.2.6+ (32 bit) connected with NRF52 DK, it is throwing an exception
...
