Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hello,
I am newbies on nrf51 and keil uvision 5.
I just start to learn nrf51 development.
I saw that with keil 5, it is possible to flash Sofdevice directly from IDE...
Maybe the question is abnormal, but is it possible to make the NRF24LE1 chip work on the Sub 1GHz band by setting the quartz to a lower (less than 16 MHz) frequency? Has anyone...
Greetings....
Since logging is removed from Mesh, I find it is very hard to debug the system. I wonder if it is possible to ask for your help to have a new monitor type...
SDK v15.2.0 using code from the peripheral spi example. Linux Ubuntu 19.04, uploading to nRF52 DK.
When I call my get_bma253_accel_data in main, I get a continuous stream...
The development of the custom hardware of an nRF52832 utilizing the u8g2 library has been shown to control a small display 64x48 SSD1306 driver. The prototype hardware another...
I have been migrating a project from SDK 14.2 to SDK 15.3 and have encountered an issue with UART. I am using the legacy layer with the following configurations:
I am...
Hello,
I'm evaluating nRF52811 as a long-range IC in a beaconing application.
Here's our specifications:
- The beacon must operate with Coded PHY
- The application...
Hi everyone, I know that the theoretical limit for the Bluetooth Low Energy throughput is 1 Mbit/sec, but I heard that on practice you get much lower. So I would like to find...
We were running BLE DFU bootloader for nrf52832 based on sdk 14.2; this worked fine.
We have now moved to sdk15.3 and nrf52840 as we needed USB.Our applicaton is up and...
Hello,
I have a custom nrf9160 device which requires
device stops at:
'Secure Boot: prepare to jump to Non-Secure image'
if I use this the following prj.conf:
...
Hello,
i I’m have a custom nrf9160 board. I have been using SES with j-link edu to upload firmware to my board with no issues.
Now I need to update modem firmware...
I'm trying to update my NRF52832 running s332 v5.0.0 and a stock SDK14.0 bootloader to S332 v6.1.1 with an SDK 15.3 bootloader.
I am including the flags --sd-req and --sd...
Hi All,
I am working on an NRF application that communicates with a specific mobile app, sends some measured data. Everything works fine except on some older (at least it...
Hi.
I wonder which pins are AIN0, AIN1, AIN5 AND AIN7 (on nRF52810 QFN32) ?
It seems the datasheet would tell...
I need this for a project at work.
Please. And Thank...
