In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Hello Nordic!
I'm developing with nrf52840, s340, and SDK 15.3.0
Sometimes, I got an error in app_error_fault_handler.
This is information that gives me in app_error_fault_handler...
Hi DevZone,
I am developing an application that needs to use UART communication with the nRF52840 pca10056 board.
I am using Segger Embedded Studio V4.16
I checked...
Hi everyone
I setting my nRF52832 is central and iPhone(iOS 12.3.2) is peripheral and using "ble_app_uart_c(SDK15.3.0 s132 v6.1.1)" sample program. I print the debug message...
I want to mask ble interrupt（only ble interrup other is work）for temporary time and then to enabled ble interrupt ?
how to do it?
thanks for everyone answers!
Out of 10 prototype boards, we have 3 not working well due to 32 KHz xtal issue.
7 units are OK, but the other 3 units works only when configured with internal RC osc. ...
Hi,
I have been hired to migrate an NRF51 project that has S310 to an NRF52 one on S332.
I have looked at the migration guide in detail and had some follow up questions...
Hi I am having a hard time implementing DFU using SDK12.3 / nRF52832 now. I have tried so many times, but have failed a lot and have left a log similar to the next one in...
Hi,
I am using v0.4.0 ncs sdk.
I added following in the nrf9160_pca10090ns.overlay file
I added following in the prj.conf file
I added following in the...
I made a Windows application that makes USB connection with nRF52840. You need nordic_cdc_acm driver to use it with windows 7. Can I distribute the nordic_cdc_acm driver with...
Is it possible to route a signal derived from internal clock to an IO pin? I am new to NRF micro controller. My experience has been with Cypress PSOC and in the IDE it was...
I am trying to implement a struct that will be saved in non-volatile memory. Does the dev kit have these capabilities on its own? If it does is there a guide on how to use...
Hello,
I am using secure dfu with bonds (SDKv15.3, Segger, nrF52832), it works fine however after each dfu (application only) I lose the bond information.
I have search...
I am trying to communicate with PN7150 from nRF52840 DK using I2C pins.
PN7150 needs 3.3V and nRF52840 is supplying 2.9V.
I am able to read PN7150 on Arduino Mega but...
I made a Windows application that makes USB connection with nRF52840. You need the nordic_cdc_acm driver to use it with windows7. May I distribute the nordic_cdc_acm driver...
