Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Saw this post from about 1 year ago.
Any updates regarding USB host firmware support on the nRF54LM20 or any timeline for when it is expected to gain some level of support...
Hi,
I'm developing a Channel Sounding application on nRF54L15 and trying to understand how the different TX power settings interact.
I have a few questions:
What does...
DevZone Post: Custom nRF54L15 Board Not Recognized by Kconfig (Falls Back to Apollo4X)
Summary: I am bringing up a custom board based on the Raytac AN54L15Q (nRF54L15)....
Hello
When following the guidline of a new way to extend boards , VSCode "Add Build Configuration" is blank. Am I doing something wrong or this is not yet supported by...
HI
I’m currently using NCS 3.2.1 , working with the periodic_adv_conn sample.
On the advertiser side, after receiving data from a node during each periodic sync broadcast...
Environment
nRF9151DK.
Using nRF tools and SDK v3.1.1 & also v3.2.3.
Based in New Zealand and currently on Spark network.
Issue
Trying to run the sample app...
Good day,
We are developing a board with a nRF54L15 + nRF7002 for BLE and WiFi connectivity.
The Nordic nRF54L15 + nRF7002 reference design has been a good starting point...
I see this errata: https://docs.nordicsemi.com/bundle/errata_nRF54L15_Rev2/page/ERR/nRF54L15/Rev2/latest/anomaly_L15_24.html#anomaly_L15_24
It says this:
"Symptoms ...
Hi, in order to be familiarized with the transceiver we have purchased an evk nRF9151 from Nordic.
I have some questions because an issue appears when I try to modulate...
hi guys,
I am using the nRF54L15 for software development. I have a requirement to define a space in the chip's internal flash for data storage. I referred to the soc-flash...
I have been experience that the if the device under a DFU process reports the error BUSY, because the external flash on the device is used for fileaccess the DFU process from...
Hi nordic support:
Our product uses the nRF9151 and prepare for GCF certification testing , which need to capturing LTE mode trace log .
We first intend to try running...
Hello everyone,
We are currently working on a project that uses the nPM2100 to power an nRF52840. Our application requires automatic enabling break-to-wake mode each time...
Hello DevZone,
One customer used Timer+PPI+GPIOTE to simulate an UART. Now it works fine.
However, when there is other timer's interrupt, the simulated UART may lose some...
