I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello,
I have been trying to merge the pwm_library (or gpiote) with ble_uarte examples to have controle on the pwm signal through UART events
I think i merged correctly...
Hi everyone.
I'm trying to transfer new firmware over UART for just only one node in mesh network.
My node will connect to other wireless MCU(ESP32, ESP8266....) over...
I'm using FreeRTOS and trying to get push button events to fire. The events would fire if I held the button down long enough. I found out that the problem was that "FREERTOS...
Hi
I have a custom board implementation that operates as follows:
Monitoring an input pin waiting for low high transition, BLE advertising of device.
When input event...
I'm having trouble having multiple characteristics for my custom service. My main.c looks like this:
Even though I have 2 characteristics added here, I can see just the...
Hi,
I had a few nrf51822s lying around and as I find the chip and the SDK quite convenient to use, I thought about using them in a small MCU project which does not need...
Above you can see the original and commented out modified code for the given example. The modification causes crush to
NRF_BREAKPOINT_COND; // On assert, the system can...
Hi,
I was looking at the Thingy-52-to-nrf52xx demo. I want to capture raw motion data no a DK and save it for further processing. Are there any options (I guess one is nRF91...
hi
i read in earlier questions on the devzone that nordic offers to review the schematic and layout as well as perform tuning free of charge to their customer. Is that still...
Hello every!
I am testing FATFS example with nrf5284 PDK .
CLK - P1.15
MISO - P1.14
MOSI - P1.13
CS - P1.12
My micro sd card module work correctly with STM32 MCU. I...
Hi all,
I am Using SDK15, chipset is nrf52810 , In ble_app_uart application i have added the BLE_NUS_C and TWI application code , before this i have added only TWI to ble_app_uart...
This blog describes how to set up SES (Segger Embedded Studio) for use with nRF SDK:
https://devzone.nordicsemi.com/b/blog/posts/segger-embedded-studio-a-cross-platform...
i'm using DFU for my project, it worked fine until devices has been bonded , DFU cannot work again. i checked and find out that after running interrutps_disable() , the devices...
Hello, I am using an nRF51822 chip, configured to run as a SPI slave. The device receives commands from master, sends commands out of the radio, and relays back RF payloads...
