When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hello to all,
I am using nRF52832 sdk15.0 version with SES IDE. I want to find adverting with short for e.g.--->
we have BLE app_uart peripherals and one multilink central...
Dear Nordic engineer,
Here is a question when we use the chip's automatic response function, the MCU PRX can download the packet, but PTX can not receive the ACK signal...
Hi.
I'm busy to add the nrf8001 BLE module to my PIC32MM product for negative pressure monitoring in a small area. Is there is list of minimum settings that is available...
Hello,
I'm having issues with the advertising module in SDK 15.0. I basically want the device to fast advertise for 3 minutes and then switch to slow advertising forever...
When I configured POWER_CONFIG_DEFAULT_DCDCEN =1, I found almost no change compared to the case of dcdc, but when I added APP_ERROR_CHECK(sd_power_dcdc_mode_set(NRF_POWER_DCDC_ENABLE...
Quite a generic FreeRTOS question probably here but... on an interrupt, what's the stack the ISR uses? Is it the one from the stack that got interrupted? If so, I guess that...
HI!
I'm using two nRF52840 boards to communicate using ESB. The ESB API doesn't have a pairing protocol so I figured I'd write one without encryption or any bells and...
Hi all,
when I insert ble_nus into mesh_gatt . I realized there are two pulse functions with the same function:
and
if they let them coexist , when I use nrf_connect...
Hi
Using the iOS 'nrf Mesh' application I can provision a PCA10056 succesfully.
I have written fimware image that sniffs for mesh related becaons, and when I power up...
I want advertise data only change with uuid for every 100ms I gone through the nrf 51power consumption guide I guess its same for nrf52 any help for changes or must have points...
Hi,
I'm using multilink Central device with SDK9.0 and stack S130. I'm able to connect to multilink peripheral device as expected. But i am not able to connect to a Custom...
Hi, is it possible to check the current configuration of a GPIO pin? I mean if the pin is currently configured as input or output. Next I need to uninitialize it and reinitialize...
Hi,
the Nordic nRF-series SoCs have got the restriction, that the power has to rise from 0 V to 1.7 V in 60 ms for a guaranteed POR. In our application we cannot guarantee...
We use nRF52832 on our product. We need to update the application remotely in the field using smartphone with BT. The unit in the field will already have an app running on...