Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I use s110 v7.1.0 ,nrf51822qfaa.
now I find the pstorage_store work is OK if I is not run sd_ble_gap_adv_start function.
but I fin the pstorage_store work is wrong if...
I use s110 v7.1.0, nrf51822qfaa.
The write flash data using pstorage is OK ,before ble_advertising_start() function is start run.
But if I run the ble_advertising_start...
Hello,
I am using the nrf52pdk and am wondering if there is a way to force an output compare interrupt to occur. For example, lets say you want to generate an interrupt...
Hi,
on the nrfprog you can detect all connected Segger programmers.
If I have 10 Segger Programmers connected, I can address each of them with the nrfprog to programm...
Hi,
I am new to Nordic. Will someone help me figure out what is wrong with UVision V5.16a. I get sample codes from pack installer example the "ble_app_hrs_s310_pca10028...
I've followed the instructions here to try and get my J-Link debugger to run in bootloader.
I am using a newer SDK and SD (than the post was written for) so that may have...
Hi !
I have a rather strange problem: 1 packet is transmitted for 30 milliseconds.
I use iPhone-4s with iOS8.1 and custom board with nRF51822
In the firmware exists 4...
I saw that DA14680 from Dialog comes with a 30uA/MHz processor.
Although the clock can be programmed up to 96MHz, the 30uA/MHz is measures at 16MHz.
How can I get a...
Can you please clarify what the RBC_MESH_EVENT_TYPE_CONFLICTING_VAL is used for with the RBC mesh? I receive these events on the node that sets a value, but not the remote...
Does the bootloader from SDK v9.0.0 actually work?
When I try to use it (with S130 v1.0 in eclipse/gcc), I get NRF_ERROR_INVALID_PARAM from pstorage_register called in...
Hi all,
After receiving data from my host app, I am trying to write to write the data to flash with the sd_flash_write command. I have 3 pages of data to write, so need to...
Is it just me, or is the documentation for SDK 9 broken? When I try to access the end nodes(where the actual info is), I get a blank screen. I'm having to use the docs for...
Hi,
My nRf51422 based device holds bonding with single central device and once it bonded it will do whitelist advertising at connection lost (whitelist has one address)....
When I send the command to the 51822,so the 51822 ready to DFU,but wait for a long time,51822 is staying at a DFU state,that means 51822 can not work.How to solve this problem...
