I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Hi all,
In my application, I take mac address of chip and make major, minor value (device 's ID) and I need mac address is a constant value. As I know, mac address is a...
because license is so expensive, I'm converting my project to OSX GNU
I'm solving problems step by step..
and there is error that I couldn't understand.
Anyone can...
Is there any way to control BLE shield 2.1 from PC rather than android / iOS app.
Also if i pass any message to BT dongle how to check the received messages.
And in...
infocenter.nordicsemi.com/index.jsp
I see a debouncing filter in the block diagram of NRF52 preview DK. Isnt debouncing implemented in software? So why need a HW debouncing...
Hi all,
I have two kinds of NRF24LE1 devices(A and B), and I want to realize that one device_A can communicate with 10 device_Bs at the same time. To explain it in detail...
I would like to use 3 PWM for controling RGBs. I use a softdevice because I want to control the pwm trough the MCP. But for now I just want to get it work to initialize these...
whether linux and bluez implemnted the simultaneous master and slave connections......?
or is it part of link layer only..?
does this feature need kernel support or not...
In the NRF51822 reference manual, the debug interface mode initiation routine is described as follow:
150 clock cycles with SWDIO=1.
I have already verified that a standard...
Hi,
I am wondering about the Cumulative crank revs for service 0x1816 & 0x1818
Cycling Cadence and Speed, Cycling Power Services
I dont understand why the crank revs...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Ok, so I've been trying to get to the bottom of a problem for a few days now where suddenly the app_timer is acting like it's on crack and running super fast, i.e. triggering...
hey,
i want to discover the PCA10001 board with PCA10000 board in master emulator. i have programmed the blanked PCA10001 chip with softdevice(s110_nrf51822_6.0.0_softdevice...
I want to generate PWM.
I set timer2 events_compare[0] to toggle pin 1:
sd_ppi_channel_assign(PWM_LED_HI_CHANNEL, &(NRF_TIMER2->EVENTS_COMPARE[0]) ,&(NRF_GPIOTE->TASKS_OU...
