I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
Hello, On nRF Connect for VS Code extension v2024.9.87 and v2024.9.31 , a USB connected J-Link probe (Segger Edu Mini) no longer appears under "Connected Devices".
J-link...
I have a nRF52840-DK that I know that it has a JLink on board, but the RAK4631 don´t have JLink, then I am following the RAKWireless bootloader update( Bootloader update ...
Hi everyone,
I'm currently developing an application supposed to read through SPI from an extrernal SRAM, i'm using nrfx_spim libraries.
Compilation is flawless but when...
Settings document explain .h_set handle will be called when the value is loaded from persisted storage with settings_load().And I want to know how it work.
I put a breakpoint...
The Bluetooth connection is disconnected, but no disconnect message is printed, and no more ads can be searched, the main thread is running fine, and the Bluetooth function...
I'm trying to just do a pristine build using the Ezurio Pinnacle 100 DVK When I originally created this project from a dev board, the resource "atmel,sam0-pinctrl.yaml" and...
Hello,
We are using the nrf52832 in SES with the softdevice s112 (v7.2.0) and sdk17.1.0 in a custom board for a BLE application (that includes OTA DFU and a custom service...
Hİ,
I can connect to LTE. but somewhere which I think it might not be the signal, it can not connect and restart (reset). not return any error. if I change my location ...
Hi there,
I have purchased a Fanstel BU840XE device ( BU840XE, The longest range, Remote USB Dongle for BLE 5, Thread, Zigbee — Fanstel ) theres the link. The device has...
Hi,
1. How can the read slave interval be reduced to less than 2ms: twi_master_with_twis_slave
2. Test environment:
DK: pca10056
SDK:nRF5_SDK_17.1.0_ddde560\examples...
Hello,
I am aware that there is going to be an update to the BLE stack and you are soon releasing 2.8.0. For NCS 2.6.0 we were using 239354 for the host subsystem and...
Hi,
I use Nordic nRF52840 BLE Sniffer Dongle and this works as expected in Wireshark up to version 4.2.7. Hówever, when I upgrade Wireshark from 4.2.7 to 4.4.0, the Dongle...
In Software Maturity Levels under Trusted Firmware-M , it is stated that only the minimal build is supported, while the full build is still considered experimental.
In Running...
We have tried the following changes, but couldn't get expecting results.
Sometimes unable to pair two devices / Sometimes fails to link with one device
Could you answer...
