Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
We evaluated the BLE Mesh DFU performance on the nRF52840 and observed that transferring a 342 KB binary took approximately 36 minutes. This aligns closely with the documentation...
Hello!
Can you map the zephyr versions to the LTS versions if possible?
We are using NCS 3.02 with the zephyr version 4.0.99. How does this relate to any of the LTS...
Hello.
I am developing in the following environment. ・nrf52832 custom board ・nRF5 SDK v17.1.0
This program already supports BLE communication, BLE DFU functionality, AD...
Hello.
During production, we occasionally encounter products that exceed the reception sensitivity standards.
Of course, we only select those that completely exceed...
I need to use PPI on my custom nRF52840 board, which selects soc nRF52840 as per copying nrf52840dk. However, this doesn't enable "HAS_NRFX", which is hard to track how that...
Hi,
I'm running the location sample on nrf9151dk from v3.0.0 of nrf-sdk. Hardware details:
I have these additional configs added to my prj.conf
This is the output...
I am working on a custom Cluster Definition Using Matter Cluster Editor 0.1.0 I have created a couple of structures on the structure tab and they are not being saved to the...
I am designing a wearable device that uses BLE and UART. During the development stage, I worked with the nRF52 Development Kit and started with the ble_app_uart example from...
Hi,
What would be the best way to alter pin's functionality from UART TX ->RX->GPOUT ->GPIN in runtime? (NCS2.5/Zephyr nRF52840)
Is it supported by Zephyr/devicetree...
Hi. I can't build the hello_dect example using cmake, the build process is failed with the following error: In file included from /home/cybermag/ncs/nrf/modules/trusted-firmware...
Hi,
In this post Hung Bui states that there can only be "maximum 4 pin events, each for one GPIO pin (so max 4 pins at a time)". This is (apperently) not true since I...
While scanning for devices with NCS 2.9.2 my device suddenly stops sending adv reports after a few hours.
It seems like this might have been fixed in a recent version...
BOARD: nrf54l15 DK
SDK: 3.1.0
Hi,
I am trying to setup my low power preipheral with a new ble address via bt_id_create.
Everthing works fine when I use the exact...
Hello! I am developing an application for the nRF5340, and I am using split cores, so the controller is on the network core and the application is on the other core. I want...
Hello Nordic Support Team,
I’m working with an nRF5340 on nRF Connect SDK 3.0.2 , using both the Distance Measurement (DM) service and BLE DFU.
My application topology...
