Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hello! I purchased some nRF54L15-DK 0_9_3 boards. Recently, I have been conducting relevant tests on the nRF54L15-DK 0_9_3. I want to test the low power consumption performance...
Hi, I am using an external host with NRF54l!5 dk to test the channel sounding feature.
Can you tell me how the NRF controller supports this Cs procedure and whether the...
Hello,
We are trying to demonstrate/evaluate the BLE mesh functionality using nrf52840dk, such that a demo application does self provisioning after boot up and once self...
I am working with NRF52840 chip with SES 6.4. My application was initially developed for nrf52832 but ported to 52840 and stopped by vector catch in debug mode. I had no issue...
Hardware Setup:
Boar d: custom board using nrf5340dk_nrf5340_cpuapp
N CS Version: v3. 0.1 (upgrade d from v2. 4 where it was working)
Problem Description: After...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hello forum ,
here i m using nrf52840 customized board ;my flash is w25q64 i need to set my flash for deep power mode (sleep mode ) ;as well i need to set my supply gpio...
Hi!
The Power Profiler II Kit is an awesome piece of gear! I love it and it almost replaces power supply and logic analyser on my bench for daily work.
Would it be possible...
Hello,
I'm trying to extend the k_sys_fatal_error_handler() function to shut down a power supply and turn on an LED in case of fatal error/exception. Unfortunately, these...
Hi the Nordic Team,
I am developing the SED product of Matter over Thread protocol, now I want to customize a Bluetooth Service and Characteristic for my company's Bluetooth...
Dear Nordic Team,
I've been working extensively on creating a custom sensor driver building on Zephyr's sensor API. Throughout this process, I've utilized many available...
HI
We are currently reviewing a problem with a product currently in mass production and would like to request your assistance.
1. Development environment
- nRF52832...
Hi all
SBOMs must be created in order to comply with the European Cyber Resilience Act (CRA) directive. Zephyr makes this very easy:
west spdx --init -d BUILD_DIR west...
I have been using the SDK example ble_app_proximity to flash my demo boards nRF52840 to do some RF PHY testing on Bluetooth advertising.
It was very easy in this example...
Hi, I'm developing a device that needs to be able to securely connect to a MQTT Broker using certificates signed by a CA. In short, I already have that working when connecting...
