hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hello,
I am trying to use the HID Keyboard Demo (ble_HID_keyboard_template from arduino sdk) . I'm using a RedBearLabs Blend Arduino with the nrF8001.
It works great...
Hi ,
I have been working on an example code in SDK : nRF5_SDK_17.0.2_d674dde\examples\ble_central_and_peripheral\experimental\ble_app_multirole_lesc\pca10040\s132\ses\ ...
Hi, On our new type of 9160 based boards, we failed to create a connection with TLS socket. After creating a TLS socket Without peer verification, and trying to connect with...
Hello,
Is it possible to use the nRF5 SDK v15.0.0 and nRF Connect SW to perform DFU upgrades? Are there any compatibility issues?
Is it advisable to continue using nRF5...
Hi,
I have purchased a ESIM from https://www.taisys.com/ , which works with DUAL Profile or Two networks.
We need to enable SIM TOOL KIT (STK) for enabling the sim...
Hi Guys,
I want to use nRF52840 Dongle as "BLE central UART".
In the first step, i used a nRF52840 Dongle with a Bluetooth low Enegy app in a nRFConnet, the result is...
Excuse me:
I can't find a api to close WDT，When the chip enters idle mode, the watchdog will reset the chip，I tried to call the command in the diagram below to turn off...
Hello,
I'm using nRF52832 board and I want to use it as a controller with a third party cellular modem to connect to AWS IoT. i.e. I want to send AT commands with the UART...
Hi,
I am trying to minimize the power consumption on a NRF52840.
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/optimizing-power-on-nrf52-designs states...
nRF52840 can support matter (BLE + Thread).
it is noted at https://github.com/project-chip/connectedhomeip/tree/master/examples/lock-app/nrfconnect
even that have a demo...
Excuse me：
How to get profile QDID，host QDID and controller QDID of nrf52832？The current SDK version is nRF5_SDK_15.2.0_9412b96,Soft device is S112,thank you!
My goal is simple. I want my nrf5340DK to communicate with my nrf24L01+ Just to test the water and also because I have experience working with the nrf24 modules. Is there...
[ Problem ]. When communicating with the TestApp as shown below, it is taking an unusually long time to get a response. The problem is that the response takes more than 0...
Hello,
I’m currently trying to flash the blinky code (found in the ‘Getting Started’ section) onto the nordic nrf9160-dk.
The error I’m getting is :
“error: cmake...
