I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello Nordic support,
I am developing a Zigbee application based on FreeRTOS for a device with coordinator role. I was able to add the Zigbee stack and start the Zigbee...
Hello,
I am using the NCS v1.5.0 and a custom board with the nRF9160. In my case, I am using only MCUBoot as the bootloader and would like to validate a firmware image before...
Hello I'm using saadc sdk (v17.02) and I'm using a simple water level sensor.
I am asking a question because there is something strange about reading this sensor through...
Hi !
Sorry about that simple question but I couldn't find any documentation about what I want to do.
This is a fairly simple issue. When building a program using TF-M...
Hello,
I need to handle 2 buttons so I configured GPIOTE. The issue I'm facing is that this IRQ occurs only once, when I press both buttons for the first time.
The ISR...
Dear Nordic,
we are starting a new project based on nRF52832 and we would like to use ANT+ communication, BLE central and BLE peripheral at the same time. To better manage...
Hi, dear Nordic & all：
I have a question about upgrade bootloader.hex, that is : Can I upgrade bootloader part when develop on nrf52832 with nRF5_sdk11( nRF5_SDK_11.0.0_89a8197...
Hi there,
We are currently conducting tests on the nRF9160 using the LTE Serial Modem app. We do however have issues testing the RAI feature on the device with an LTE-M...
Hello I would like to use the crypto example in sdk v17. However, when I try to build it, the following error is output:
I've done a few things while looking at the forum...
We are referring " ble-characteristics-a-beginners-tutorial " to create a custom service.
I want to modify security permission from "
BLE_GAP_CONN_SEC_MODE_SET_OPEN" to...
It looks like even with the latest SDK 1.6.0, the full modem firmware pre-validation is turned off.
It looks like this is a modem firmware feature, so it would seem that...
Hi All,
I am new in the Dev Zone and apologize in advance if the question was posted in the incorrect section.
I would like to run the Thingy91 as tracker hardware for...
Is there any API (software) available to evaluate DWM3000EVB module on nRF52 DK?
Can we use the API/software available for nRF52840-DK for nRF52-DK as well?
From where...
