I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi, Is it possible to order nRF5340 QKAAD0? This one is on DK and the last IC version? As I can see, your distributors e.g. Mouser only have nRF5340-QKAA-AB0-R/R7 but this...
Hi,
I am using nrf52832 development board with s132 softdevice and SDK17. I want to add the DFU service to this application so that I can update the firmware to the device...
Hi,
In the Enhanced Shockburst User Guide, there is a brief discussion about the required bit pattern of 1st on-air byte of the base radio address
(which immediately follows...
If I use nRF Connect to connect to the Peripheral and the Subscribe to Notification Characteristic I can see in the "Enabling notifications" in the log (however no notifications...
Hello
I use sdk v17.0 and nrf52832.
I'd like to use 1-channel PWM and 2-channel PWM. However, an error is output from the pwm_enable when using these two together.
...
Hi,
Following are my working environments:
Product: nrf51422 Evaluation Board
SDK: nrf5 SDK v10.0.0
IDE: Segger Embedded Studio
Programmer: Segger J Link
I was...
Hi,
We have a device that is using Nordic's ESB protocol. We want to use different frequencies to avoid collisions and for that we also need dynamic frequency handling....
Hello,
I have two questions:
How do I access the gpio pins of nrf52840 dk? what example program from nrf5 sdk can I use as example?
Is there a simpler example program...
Hi engineers,
This is my timer init code. I place it before functions timers_init() and ble_stack_init().
app_init() includes led and timer init function.
Cheers...
Hi all,
I am now evaluating the BLE 5.1 supported chips. I see that s140 support ble 5.1 but I see nrf52840 can't support aoa. Is that I need to use nrf52833 with s140 softdevice...
I have tried this demo (SDK17) on a few different Windows machines and they all give the same error for me. On plugging in the SDK after loading the demo Windows tells me...
There is a similar case where the user mentions that he fixed his issue by "changing the compiler" with no further explanations. https://devzone.nordicsemi.com/f/nordic-q...
Hi
I am using nrf52832 (S132) with SDK17. I want to store some data in the flash memory dynamically. So what would be the maximum and minimum flash memory that I can utilize...
I would like reduce TX Power in DFU secure bootloader, I would like use sd_ble_gap_tx_power_set function but I faced with the following problem, I don't know how to get conn_handle...
Hi
I am working on the GPS for Thingy91. The Thingy91 is able to get the fix when I am outside and test it. However, when I am in the building by the window or on the balcony...
