I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello everyone,
I'm trying to interface a NiceRF LN610 LoRaWAN chip to nRF52840 via UART. Initially, I tried communicating with the chip using CP2102 USB-to-TTL module and...
Hi,
In order to measure the RF power, I measured the RF power by radiating inside the RF shield box.
But there is something strange.
The position between the device...
Hi ,
I want to develop the firmware to read the nfc tag and read the sensor data send to the application via BLE I have read many post regarding nfc . Let me explain what...
Hi,
I am working on temp. sensor with nrf52832 dev kit for firmware testing and development and also using nrf52810 for product testing.
in my code, I merged twi communication...
hi,
I want to develop a project based on ble beacon mode and ble app hts code.
and I am using nrf52810. so will it work if I merge both codes and use for this project...
I know that nrf_cal_set_time() from the nrf calendar example is NOT meant to be called on a regular basis / should only be called to update the time being kept locally to...
Hi,
We are looking for a guideline to trigger GPIO and SAADC sampling at the same time.
Our purpose is to sample every 20 m
Hi,
We are looking for a guideline...
Hi, We have a DFU OTA process that was functional, but updating our softdevice to s113 7.2.0 has left us with a problem - since the softdevice does not exist in the nrfutil...
Hello.
I am doing a small project where nrf52 reads data from a BME280 temperature sensor via SPI and sends it using ESB.
I have no experience with radio, so I use a ready...
I would like to use the NRF24L01+ from a 3v coin cell, but interface it over SPI with a 1.8v-powered microcontroller. Assuming the uC is tolerant of the NRF SPI outputs, I...
We have a application where data transfers happen through a mechanism where the external client does a write-without-response to send in a command. The response to the command...
I am busy with my first BLE project , programming a custom service for both pheripheral and central role. I have already finished the pheripheral service, using a custom service...
There are other GPS modules on the market which can give information like "the device is within 10 meters of the given coordinates". Is there a way to either get this information...
Hello,
i am using AES CCM encryption available in nrf52832,
my data which need to be encrypt is same every time. data will encrypt and 4 byte will add at the end of...
Hi all,
I am working on a project with the nrf52832 and I am using softdevice S132 6.1.1. After creating my desired flash layout (with some help on this forum, thanks!)...
