Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
I am developing a custom board using nRF52810.
SoftDevice S112 6.0.0 and SDK 15.0.0 are in use.
I want to know the maximum current in Idle state .
Current measurements...
Hi all,
I am currently trying turning off the active time, so that the nrf9160 immediately goes in power save mode after RRC Connected Release.
If I send the command ...
I connect VBUS to VDDH, and use a USB cable for power supply(high voltage mode), but I cannot download firmware into the 52840.
Unless I power the 52840 from the VDD pin...
Hello,
I'm a teacher. I use the microbit card that loads one of your components. Nordic nRF51822-QFAA-R rev 3 Could you tell me if this processor is based on a Von Neumann...
Hello, just a few quick short questions regarding nrf52 devices:
Do I have to configure and initialize them before using?
Which function should I use? I...
Hello, I working for TSS.se now selling 100.000 temperature-loggers annually. We aim to develop a new IoT based logger based on nRF52832 as a replacement.
Issue-background...
Hello,
nRF52840-DK
SDK 15.3.0
SoftDevice: s140
IDE: SES
Example: Flash_fstorage_s140_pca10056
I do not read back the expected value in the example. The terminal...
Hi, I am trying to do DFU OTA. I am using SDK v16.0, s140_nrf52_7.0.1_softdevice.hex, SES and nRF52840 dev kit. I am finished with my application and it functions as expected...
Hi,
We are a module manufacturer. We are making modules based on WLCSP, QFN based nRF52840 SoC.
Can you please provide software(preferably GUI) available for module FCC...
Hi guys, i can't figure out how to create an event handler in my Mesh Client.
The functionality of this handler should be to set a flag on the 'NRF_MESH_EVT_TX_COMPLETE...
I used keil v4 compile the following project F:\nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral\ble_app_uart\pca10040\s112\arm4\_build get file nrf52832_xxaa.hex of size 101kb...
Hello ...
I'm porting our product from RF Digital's Simblee to Laird's BL651 (nRF52810). A phototransistor measures light, is connected to an analog pin, and is sampled...
Hello guys! And girls
My project is working as expected in SDK14.2. I'm updating adv data (manuf. spec. data) without any problem with this function But in SDK15 the function...
