I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
HI,
I've noticed a few issues with the example app_level.c.
1: The g_set_transition() was updated in the 3.0.0 release to avoid a division by zero, however, this fix...
Hello all,
I recently migrated from SDK 15.0.0 to SDK 15.3.0 and as a result tried to migrate from SD 6.0.0 to 6.1.1.
My application goes to sleep after a while and when...
I am new to this environment.
Attempting to create a simple BLE app similar to the built-in BLE, but with some buttons to send predetermined commands to devices. Using the...
I applied Bonding to the UART example(ble_app_uart).
Bonding combined with the UART example works well, but there is one problem.
1. I did Bonding first. 2. After that...
Basically I get an Attribute not found error from sd_ble_gatts_value_get() in the nus_ble.c and then I never get any NUS events in the application. I'm trying to figure out...
Hi!
We have working solution with custom rf protocol based on NRF52832 and NRF52840(now it use 2 Mbps Nordic proprietary mode). Now we want improve it.
Could You give...
HI,
I have found some problem with nrfutil (version 5.2.0 installed from pypi).
Problem description:
When I am updating dfu with success (correct keys, packages etc...
Greetings,
I'm using 3 NRF52832 boards, s132 and SDK 14.2.0. I'm interested in connecting two hrs peripherals to a single hrs central, but have found some posts that say...
When creating an attribute specifying vloc as BLE_GATTS_VLOC_USER, it is not very clear that a storage pointer must be provided on creation of the attribute and cannot be...
Hi,e verybod, I use nrf51822 to do bluetooth keyboard, I hope the function is: After bluetooth keyboard connect the host,how to determine whether the connection is window...
I'm trying to create a virtual beacon on an Android Phone using nRF connect V4.22.3. Android Version on the phone is 8.1.0.
I've enabled a beacon using Advertiser. However...
In an BLE example I have a characteristic with the value 0x00001234. In the nRF Connect 2.0 for iOS i see the value 0x00001234 and in nRF Connect for Desktop v3.1 i see "34...
Using the logging module in ncs v1.0.0, I see some extra characters after the timestamp " <0x1b>[0m<inf>" and at the end of the line ", is there a way to fix this?
The terminal...
Dear All,
I am fairly new to the nrf9160 and the Zephyr Os.
I am trying to write a simple example code for watchdog. All I want to do is to reset my board if I don...
