When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hello,
i am finding that after i call app_timer_cnt_get() there is a constant power drain.
I have an Ultrasonic sensor. the ECHO pin will fire 2 times into a GPIOTE...
hi.........
how to add the timer mode in hts program , i want to set the timer in my program to receive the data according to timing .
i am using segger 15.2 version ...
When I power the 52840 from a LiPo connected to VDDH and using VDD/VEXT to power 3V3 components, when the chip is put to sleep is the output on VEXT switched off? Or do I...
Hello, above is the PWM modulation waveform (positive Xuan Bo).
How does 1.nrf52832 regulate the frequency of circulation?
Take this nRF5_SDK_12.2.0_f012efa\examples\peripheral...
Hello, I want to use nrf52832 to output waveforms as shown above.
Using the Demo1 example in D: Lianxi nordic nRF5_SDK_12.2.0_f012efa examples peripheral pwm_driver, we...
I am sending 6 packets of 20B each data using ble_nus_string_send() function at every 120ms using app timer. but the function returns error BLE_ERROR_NO_TX_PACKETS. So unable...
From the latest Nordic SDK 15.2, I'm running the usbd_cdc_acm example on an NRF52840 connected to a PC using USB. The firmware correctly executes the USBD_POWER_DETECTION...
Hi,
I develop on nRF52 with linux/eclipse but to debug, I would like to use the sniffer. This one is only available on windows then I try to install it on a Windows 7 64bits...
I have successfully implemented Scanning and Advertising at the time using s132 on nrf52832 with SDK14, it works very stable and fast which satisfied me.
Recently, I was...
Hello,
I've been using the SDK 15's "ble_app_uart" example and I've been curious on how the function nus_data_handler() gets called after data is sent over BLE. More specifically...
hello,
I am newer to nrf. I am using nrf52832 development kit and using soft device 5.0.
I have confusion with two function with nrf_log_info and printf?
which should...
Hi,
I want to know if we can send Mobile Notifications or send sms to nRF52832. i want to do some operation based on notification or sms received from sms on mobile..
Hi,
I am currently trying to setup my sdk 15 on my pca10040. I already have a working I2C source for a BME280 and it works fine using the SDK 12 (pca10040), I get the current...
