Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
I'm attempting to build the ble_app_hids_keyboard example from sdk 14 using gcc and the compiler is throwing the error "No such file or directory", but the file is there and...
I have problem on SoftDevice V6.0.0(nrf52832) scan_start/stop. modified ble_app_blinky_c(ble_central) 1. app_timer add (20ms cyclic) 2. app_timer handler, run sd_ble_gap_scan_start...
Hi
The 'ble_app_multiperipheral_pca10056_s140' example for the nRF52840 has an 'LED' characteristic under which there is a "Nordic LED Button Service"
The value...
Hi,
I've defined:
#define NRF_SDH_BLE_GATT_MAX_MTU_SIZE 120 (in sdk_config.h)
I get "Insufficient RAM allocated for the SoftDevice" in nrf_sdh_ble_enable
nrf_sdh_ble_enable...
Hi everyone, I'm looking to buy nRF52840 SoC for my thesis but I'm surprised that none are yet available from Farnell, Mouser or Digikey ... I found few chips on Symmetry...
Dear Engineer,
We are working on 52840 usb dfu,program softdevice s140_6.0,
and usb secure bootloader,
evaluate board is pca10056,v0.9.0
Led1,led3 turn on once load...
I am very new to ARM controllers. All of my experience is with Atmel family, which I've been using for years.
I just got the nRF52 Development board and have loaded several...
Why do the version numbers have to be as follows for a merged hex file to be able to exit the dfu mode when flashed externally as a combined hex file (SD +BL + BL settings...
With the BT 5 extensions, is it now possible for BLE Peripherals to communicate with each other without a Central ?
In the envisaged application, one node would be the central...
Hello,
my problem is reproducable with this Setup:
nRF5-DK with ble_blinky_example (central)
nRF5-DK with ble_blinky_example (peripheral)
Press Button1 immediately...
Hi,
We are using nrf8240 SDK15 and need to convert soft image which is in hex format to binary format. Tried using 'arm-none-eabi-objcopy' for this. It converts 424kbytes...
Hello Nordic team,
I am developing a proprietary radio protocol and i am using aes ccm peripheral for encryption (i am a begginer). The packets seem to be correctly encrypted...
Hi,
Can you guide as to how to set up an proxy node that participates in mesh activities as well as connects with an non mesh device (viz Mobile) from time to get data from...
I’ve been working in a small group to use the advertising extensions in BT5 to send 12 hours of temperature measurements in one advertising packets. We’ve been developing...
Hello,
I am working on ble/audio application on nrf52832. I would like to know how to compile OPUS codec (used in smart remote) so I can use it on arm cortex. For now I...
