I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hi all,
We are working on a project that uses the nRF5340 and nRF7002 combo. In our application, the device enters a low-power mode on the nRF5340 during sleep, with the...
Hi,
As the subject, when i connect to the Windows with the cable connected with VDD side, it will not show up Jlink in Windows.
What should I do to reset the Nrf5340 ...
Hey everyone, I am looking for big size capacitive touchscreen for my next project so I do found with resisitve touch using FT810 EVE graphic controller with nrf52840( https...
I was trying to get a simple Zephyr project to build and run on the Arduino Nano BLE 33 which has a NRF5248.
In VSCode with the NRF plugin I select "Add build configuration...
I have a PCA10056 (nRF52840 DK) and while programming it with a UART example from the nRF5_SDK_17.1.0_ddde560 using Segger Embedded Studio for Arm 5.42a, it will not show...
Hello, I have one smartphone with Android and one ith iOS with NRF connect application and I can't see, only on iOS, the Primary and secondary PHY used by my advertiser device...
Hi everyone,
We have devices using the BLE module (nRF52) deployed in clinics for testing. They have been functioning without issues until recently when we noticed occasional...
I'm using the nRF54L15-DK to run a Bluetooth peripheral_hr project in DCDC mode, but if I write
nrf_regulators_vreg_enable_set(NRF_REGULATORS, NRF_REGULATORS_VREG_MAIN,...
Context: I am working on a project to monitor up to 880 devices in an Industry 4.0 warehouse. The warehouse is divided into 16 areas, with each area housing 30–55 devices...
Hi everyone,
I’m a complete beginner and need some help. I’m working with two XIAO nRF52840 Sense boards: one as a central and the other as a peripheral. My goal is to send...
Hi,
I am trying to use a digital channel to sync with a current measurement. I have connected VCC, GND and a digital output of my DUT to the PPK2. I can see from the scope...
I am evaluating a Fanstel BC805M device, which uses the nRF52805 chipset. I am using VSCode and have installed the nRF Connect Extension Pack, toolchain v2.8.0, and SDK v2...
I programmed a nrf52840dk board (PCA10056 3.0.0 2022.7 1050288497) as a sniffer. It works well.
Now I want to flash it to zephyr samples/basic/blinky by "west flash". west...
