I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
I am using SDK 3.1.1. I am trying to use the "sensor get" command with the internal die temp sensor.
In theory, this is all off the shelf software. I didn't write anything...
While running scan & connection tests with NCS 3.2.1 , I encountered frequent connection timeouts ( bt_hci_core: Connection creation timeout triggered ) when using the Nordic...
I'm using the Power Profiler Kit II to measure current draw of an ESP32 board at idle. The PPK2 is connected to the battery terminals of the board (XIAO ESP32-S3) and whether...
Hello, I should like to enquire whether the nRF54L15-DK development board supports both Classic Bluetooth and Bluetooth Low Energy. Having reviewed the relevant documentation...
Dear All,
I'm following the nRF Connect SDK Fundamentals and I have a weird problem in the Lesson 3 exercise 2, section "Adding custom configurations".
The part with...
Hello everyone,
I've been testing the "central UART" with a "peripheral UART" (NUS) examples with two nRF54L15 DKs (nRF SDK v3.2.1 in VS Code). So far, everything is working...
Hello everyone!
I have a question regarding nRF9151 and the new DECT Hello sample. I have installed the newest version of the SDK, a preview of v3.3.0, built and flashed...
Hi!
NCS 3.1 On a custom board with nrf5340 and nrf7002, h ave successfully implemented and tested FOTA over Bluetooth Low Energy with Simultaneous updates for both cores...
Hi,
I'm trying to reduce the power consumption of my Matter Temperature sensor code.
I'm averaging around 90µA of consumption, but I'm confident that can be reduced. ...
Hi,
I’m having trouble getting an ISP1807 (nRF52840) to run on a custom PCB, and I’m hoping someone here might recognize what I’m missing.
Hardware / setup
Module...
Hello, we’re currently facing an issue regarding the start-up of the nrf9151 modem. Its a custom PCB and closely follows the schematic of the nrf9151 DK. For first test SW...
Hello Nordic Engineer,
I know that I can modify #define DEVICE_NAME "device001" in sdk_config.h , but it takes a lot of time to compile and flash the program every time...
Hi,
I have flashed hci_usb example on nrf52840dongle(hci1), enabled DLE. But when linux machine requests data from other board(as sender) dongle is getting crashed.
The...
I have create a model (which is now marked as complete), but when I go to the results tab the options (and below) just show a spinning circle. How can this be fixed?
