Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
Hi, I learned how to replace the softdevice for a normal application. I've replaced 140 with 340 in my app. However I don't know to do that for the boolloader.
What I want...
Hi Nordic,
I want to control an LED with the nrf GPIO, the LED Anode is connected to VDD, through a resistor, and the cathode is connected to the GPIO. Under this configuration...
I want to use the nPM1100 to battery manage, and supply power to the nRF52xxx - along with a heavy duty load ***directly across the battery***, so that full battery voltage...
Hi,
I'm running the experimental example: 'ble_nfc_pairing_reference_pca10400_s132' using sdk17.0.2 (and 17.1.0).
After I installed the micro-ecc following the guide on...
Hello
I am evaluating design of wireless communication in power supply with nRF24L01P , and I have 4 questions.
1.I want to know the Mean Time Between Fails (MTBF) and...
I'm using softdevice s140.
My power comes from a CR2032 coin cell.
My board has a 1.8V LDO (Toshiba TCR3UM) because my temperature sensor is calibrated for 1.8V (TMP112B...
Hi,
Looking at the source code for nRF Connect SDK v1.7.0-677-ge3c356ec8 and SDK For Mesh 5.0.0 I can't find any indication that the following section of the Mesh Profile...
Dear Nordic,
we are devepoling FW based on nRF52832, SDK 17.0.2. We have 2 devices:
BLE Central with SD S332
BLE Peripheral with SD S112
We setted up an open BLE communication...
hi all,
i am using sdk v8. i want to on rtc when button is pressed and i want to off the rtc when it is released.
i am using bsp_handler only for button press.
PROBLEM...
Hi,
I am a little confused between GPS and AGPS sample code provided by nordic. can you help me to understand it?
I just want to send GPS and accelerometer data of thingy91...
I am trying to build the ncs example direct_test_mode with the nrf52840dongle and I am running into these warnings on build in vscode:
I do not understand what it means...
I tried using the ble nus with throughput using the example from https://github.com/LeoHJX/ncsExp/tree/master/app/ble/throughput_nus . However i kept getting an error on the...
Hi all,
I am running an cts example which is asking for bluetooth dongle is there a way to avoid bluetooth dongle,
or can u suggest any example for current time service...
Thanks in advance for the help.
I connected my 9160DK (V1.0.1), downloaded the SDK programmed img_app_bl\serial_lte_modem_2021-10-20_d29f1dde.hex and tried to follow the...
It would be convenient in my design to use a single PCB design in 2 different roles. 1. As a continuously-powered rechargeable battery device, with USB charging. 2. As a USB...
