Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
I have moved my project over to SDK 17.0. So far I have changed very little.
On compiling I straight away get a liner error: "Undefined reference to '__RAM1_segment_end__...
Hi to everyone:
As the title suggest I'm using the NRF52840 PCA10059 dongle and everything works as expected.
The issue comes that I've modified the dongle to instead...
Hello,
We have developed a new type of smartphone gamepad using the nRF52832 chip. But for some reason, it works for some games and not for others. And only partially work...
Hi,
I have problem with using nrf_serial.h, I am receiving data from Ublox GPS, baud rate = 9600, no flow control as we dont have enough IO pins.
Device is nrf52840 with...
Hello, I'm trying to integrate an SPI slave into ble_app_beacon example. Power consumption of ble_app_beacon between advertising is up to 10 uA. But if I write a byte over...
Hello
I am modifying the example of mpu6050 of sdk v14 in sdk v17.
After build, it is printed that there is no path to the file as shown in the image below.
(The...
Hello We recently went to a test facility SGS, in San Diego, with our nrf9160 device trying to get a pre-cert scanning completed to find out if there are changes needed before...
Using SDK 15.3 and S132.
I'm having similar behavior to the thread below:
https://devzone.nordicsemi.com/f/nordic-q-a/12066/gap-disconnect-stops-app-timer
After disconnecting...
hi ...
how to update the advertisement packet .. I have seen many post regarding this ,I am not getting clear , anyone can share me the piece of code which will help me
I am trying to repeat the example in the tutorial: using board: nrf9160dk_nrf9160.
nRF Connect SDK Tutorial - Part 3 | NCS v1.3.0 --> 1.2 Walkthrough for BME280 - but gives...
Hello,
Our setup:
-nRF9160
- Zephyr OS
- Segger Embedded Studio for Arm (Nordic Edition)
- SDK v1.3
Questions
1) which are the differences between Zephyr functions...
I'm designing a product around the nRF52840 (PAN1780 module), and using the PWM to drive a piezo sounder (using 2 pins as Hbridge). When I start using BLE functions, I get...
Hey, Yesterday we decided to update SDK to 17.0.2. After this change our FreeRTOS stopped working. We started investigating where is the problem and we found that when vPortSetupTimerInterrupt...
Dear all,
I'm currently using nrf52840DK with SDK 17.00 and s140 softdevice. I'm trying to syncronize the dispatch of my data with connection interval (set to 7.5 ms). I...
Using: Windows 10, nRF Connect v3.5.0, SES v4.52, ncs v1.3.0, zephyr v2.3.0
I have a custom board based on the Thingy91 and the Asset Tracker application. There is also...
