I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi,
I'm currently developing a custom bootloader for DFU, using I2C.
The bootloader is based upon the secure UART bootloader for nRF52832. Transferring and writing the...
Hi Nordic Team,
In the recent Nordic APAC Event, we got nRF52840 Dongle and we would like to use it as BLE sniffer.
Can you please point out some resource/link which...
On the NRF52840 what is the max speed I can program the unit at. In the datasheet SWDCLK says it has a max of 8MHz. Is that supposed to be the max. I have two segger programmers...
I am using the nRF52DK board.
I use the " ble_app_template_pca10040_s132 " for testing.
I want to advertise 2 custom UUID (SERVICE_DATA " 0x16 " & SERVICE_DATA_128BIT...
Hi,
We are in process of picking the right part from Nordic portfolio and are looking at nRF52 Series parts.
We are looking for best performance in below two aspects...
Hello,
SDK: 15.3.0
nRF52840-DK
s140
I have taken the flash_fds_s140_pca10056 example and modified it for our own use. I would like to store versioning information...
Hi Team,
I am working on nrf52840, for openthread application
I flashed cli code built with USB=1 (enables Nrf USB J3), DIAGNOSTIC=1 (enabling factory diagnostics) option...
Hi !
I use SDK:15.3.0 ,Mesh v3.2.0 and have tried official dfu example which is ok.However, When after I enable marco "MESH_FEATURE_PB_GATT_ENABLED=1 MESH_FEATURE_GATT_PROXY_ENABLED...
Hi,
i have designed my custom hardware using BMD-301
i'm able to upload code in bmd-301 using segger embedded studio.
after code uploaded device is not broadcasting...
Hi team, I faced the following problem: there is a custom board with nRF52810 on it, UART is used on this board.
I set up Debug configuration and UART is working OK, but...
Hi,
I am working on a project where I need to send and receive ASCII strings from my Central Device to the Peripheral Device. Before the communication starts there should...
Hi, we have an nRF9160DK (0.8.3) and it does not connect to the nrfcloud.
We have updated to the latest firmware 1.0.0
We only have nb-iot here so we didn't use the iBasis...
