Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
Using nRF connect SDK V1.0.0
File --> Open nrf connect SDK project
Tools --> Option --> nRF connect
Install all the packages described in "Getting started...
We are evaluating the feasibility of a device using nrf52840 which requires below peripherals:
3 x SPI: For MCU to MCU communication + high-speed data transfer from sensors...
Hi,
I am using nRF51822 controller. And I am using SPI peripheral to read 80 bytes of converted data from an ADC converter.
While reading spi data I realized that there...
Hi,
I have build a application based on the mqtt-simple-sample and successfully integrated TLS.
Now I wanted to measure the floor current in PSM. I did wait some minutes...
Folks,
I have a dev board PCA10040, which is running, I think, soft device s132. Additional load file is:
components/softdevice/s132/hex/s132_nrf52_6.1.1_softdevice.hex...
Dear Team,
I have a problem with one sensor on some boards, the behavior is not clearly reproducible. On some boards, the "device_get_binding("CCS811")" just delivers exit...
Section 18.6.2 of the nRF52832 datasheet (Power-On reset) specifies the following:
A step increase in supply voltage of 300 mV or more, with rise time of 300 ms...
Hello,
I have tried the GPS sample and it worked fine. Now I want to understand the code more in detail und maybe modify the GPS settings.
But I can’t find any documentation...
Hello NRF Team,
Is it possible to change the I2S buffer size on the fly while a i2s transfer is running ? (I Am using nRf52840 with SDK15.2)
I found in the documentation...
Hi, I am evaluating the nrf52832 and the Softdevice for potential use in a new product. The product has neither display nor keyboard. It therefore makes sense to use Just...
Hello,
I am quite new to developing with the nRF52840-DK. Up to this point, I have been flashing the applications (mostly the examples) over USB with the built-in J-Link...
We need to connect 2 peripherals with single central device.I have taken ble_app_multilink_central from SDK 15.3 and integrated the ble_app_uart_c in this. I am using the...
Hello,
I want to establish an UART communication with rn2483 module with nrf52-DK, SDK 15.2.0
On nrf52-DK, pins 6 and 8 are reserved for serial port, which are connected...
Hello
I used to do TWI communication until now, but it was decided to do sensor reading with SPI communication by changing the sensor.
So that's a question,
What is...
