Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
What is the input impedance or input current of port P0_30/AIN6 when operating as an ADC input? Nominal or typical figures would be OK, but maximum and minimum figures would...
1、Nrf52810 does not have VDD_PA pin, whether it needs software control, whether any pin can be replaced？
2、Is there an example of the use of PA/LNA circuits in gazell and...
Hello,
The Gazell Pairing User Guide in the infocenter states that the AES ECB block is used for encryption & decryption. However, the product specification document for...
I have an issue with bonding between a PCA10040 running the sample Glucose app and an Acer tablet running Android 7 and nRF Toolbox. I have not seen the problem on a second...
Hello sir,
I am a beginner on NRF52840. I am using Nrfx_spim example for interfacing sensor with NRF Board.
I have done some driver about Reg_read and Reg_write. I tried...
I'm using the basic sdk example of ble_app_hrs_freertos example and created two tasks in it, namely Task1 and Task2. Now I have enabled preemption by setting "configUSE_PREEMPTION...
Hello everyone,
I write datas from my Client to my Server, but I don't really understand where I can retrieve my data on my server.
Is this function allowing to get...
Hi ,
What we want is a accurate ms.
below is what we do 1. Set the prescaler config.prescaler = 31;
2.When I need the Elapsed ms, First ,I get the elapsed rtc counter...
Hello everybody!
All boards below below have nRF52832 chips.
My task now is to develop a set of applications that will support the following scenario:
1) A person...
This question comes from my high-level goal of testing I2C using the SWDIO/SWDCLK pins on the nRF52840 Dongle, so if there are faster ways to experiment with that functionality...
Hi,
I am having hard time understanding the use of "addr_id_peer:1" field in the structure ble_gap_addr_t. Could you please help me understand the usage/significance of...
Hello, Is there any intention to add the the nRF52810 reference design to the Eagle library on github? There are five Eagle design blocks already available on github, except...
Hi,
I encounter error when I debug the nrf52832 DK.
I run the example code "ble_app_uart" provided in the SDK.
Below error shown when I set the break point in any line...
Hi,
I am using an NRF52832 on a custom board and I programmed the Broadcast RX code into the board. I use ANTware as the master with a channel period of 4 and send broadcast...
Hi,
I m using nrf52840 board act as central which will connect to particular device, and discover its primary services and characteristics.I am new to nordic development...
