Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
how can i program in nRF 52840 UARTE. i want to communicate with other serial device using nRF 52840 UARTE communication (send and receive data).
can you send me the snippet...
Hi,
I am developing an ANT+ embedded device (nrf52832, SDK14.2) , that (among other things) acts as a BSC receiver. I have a BCS sensor that is seen in Garmin Edge as 136150...
I want to transfer data using UART to BLE by Baud Rate 19200(using nRF51822).
Transfer data speed need to achieve 2KB/sec up.
How can I do it successly?
Thank you...
I noticed that you have a branch called feature/v6-upgrade for pc-ble-driver. Is that branch usable for 52840 and s140?
By usable, I mean it can be mostly usable and we...
Hello,
I am following the PPK Get started get started of the PPK board.
I am developing on the NRF52-DK (Rev 1.1.0 2017.23) - nrf52832 My SDK is the nRF5_SDK_15.0.0_a53641a...
Hello everybody,
I am using sdk14.2, s132 with Nrf52832. I want to define the pin of the NRF52 as the input and decode the incoming pwm signal. For example, I have a signal...
Hello,
I am working with the BL652 EVK from LAIRD. The EVK has nRF52832 IC inside of the module. I downloaded the " nRF5_SDK_15.0.0_a53641a" and trying to use "ble_app_uart_pca10040_s132...
Hi. I am trying to develop an multiprotocol test example using SDK 15 and nRF-IEEE-802.15.4-radio-driver on NRF52840 dk board. I need that BLE and 802.15.4 stuff can work...
I have a confusion about mac address of nrf51822, I run example ble_app_uart .
When I use nRF Connect on Android, I can see the mac address of nRF51822 is CB:16:04:4A:10...
Hi,
I use nrf52832QFAA, SDK 11.0.0, Softdevice 132 v2.0.0. I need to add a device_manager_central to my project (in my project it's easier and faster than adding a peer_manager...
Hello,
In the documentation for nrf_serial_write function (SDK 14.0.0) it is written:
timeout_ms Operation timeout, in milliseconds. Pass 0 to operate in non blocking...
Hello friends,
I am trying to flash a nrf51 dk with keil5. When I try to flash it with a multilink universal I get this error:
My settings are the following:
...
Hello everybody !
My code is based on the code of the "ble_app_multilink_central" on which, I added some of the code "ble_app_uart_c" for the initialization and the event...
