Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hello,
Is it possible to configure an nRF5340 to be both a Broadcast Sink and a Broadcast Source, but with the condition that only frames received by the Broadcast Sink...
Hello,
I am measuring RSSI values with nrf_modem_dect_phy_rssi(...) from the DECT PHY firmware.
The nrf_modem_dect_phy_rssi_event refers to positive values being saturated...
Hello, I have a particularly weird problem that I can't figure out how to solve. I was using the 52833 DK for software development and the onboard leds were blinking perfectly...
Hi.
I'm fighting to get an i2c scanner (re)expose external devices' hex addresses on an Xiao nrf52840 board under VsCode nrfConnect (the basic board, not the Sense version...
Hi,
we are designing a custom board based on the nRF54L15 QFAA (QFN48) using a chip antenna with coplanar waveguide feed on a 4-layer PCB.
In the Nordic reference design...
Hello, We're improving a battery-powered (CR2032) sensor tag based on an NRF52833 with a 868 MHz transceiver. We want to use the nPM2100 PMIC and would like to optimize the...
There are two USB ports. IMCU and nrf5340. I had a lot of trouble with bad cables but i found one that works and I find that I have a jlink drive that pops up so I know there...
Dear Nordic Team,
We are seeking assistance in resolving a significant power consumption gap observed in our nRF9151-based asset tracker. While our lab testing suggests...
Hi,
I am working on a sensor device that requires very accurate timing on the sensing and sensor signal algorithm side. This device needs a low latency and low jitter radio...
Hi,
I am working on a custom board based on the nRF5340 using Zephyr RTOS with external QSPI NOR flash.
I am facing an intermittent issue with the external flash.
Observed...
Hi nordic,
I am streaming live microphone PCM data over BLE. The microphone data is continuously captured and stored in a buffer. Whenever 12 KB of audio data is available...
I am PHD student in china and doing research about gait retraining. I am designing wearable sensor that monitoring gait and giving vibration feedback to retrain the gait and...
we would like to explore the Nordic nRF52 series of low powere BTLE on coincell souerce for a waist band to dectect gait and analyse a probable fall in advance and in addition...
Hi Nordic,
We are building a product in the field of Sports, specializing in running shoes. The concept is to correct running form via analyzing the foot strike of the user...
Hi DevZone,
I am currently working on an external Flash OTA update via SQSPI on the nRF54L15 DK (v0.7.0). I have already verified that SQSPI read/write operations are...
