I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi,
Last December I started to know about NORDIC nRF5340. I thought it could be a very good SoC for developing our next BLE wireless product. Considering the huge number...
I programmed my thingy91 with lte_ble_gateway example, however I want to be able to connect to devices with specific addresses. Can anyone point me in the right direction...
Hi,
I am using pwm driver to generate different square wave of different frequencies in order to drive a buzzer to play melody.
Below is how I init my pwm software module...
I have the following problem:
1 to 3 phones are bonded with an nRF52832
These phones are on the whitelist of nRF52832
nRF52832 goes into Power Off Mode
nRF52832...
Hi,
We are integrating the nRF52840 into a new test apparatus and I am using the nRF52840-DK for development. I have pulled out my unit from storage and it will not power...
Hi,
There was an app timer immediate expiration issue with my project which is using nrf52840 + S DK 15.3.0 on custom board.
So I changed apptimer code to app timer2...
I was wondering why the RSSI Viewer Values are locked to a minimum of -33 dBm. Is there any reason for that and is there a workaround to get lower values? Currently I am using...
Hi,
I currently need to stream 1000 data samples over BLE, each data sample is 14 bit value, hence i'll be using a short integer but i'm confused as to how to send it over...
HI,
we are using the nrf52840 in our new poroduct and we are running the zephyr/ncs RTOS on it.
for real time reasons I need to read from a SPI bus upon a GPIO trigger...
Hi all,
I would like to ask whether is there any details description of the matching network circuitry of NFC for NRF52840 in the datasheet.
The only information I could...
Hello,
I am following the instructions given in this ticket https://devzone.nordicsemi.com/f/nordic-q-a/57896/pdm-interface
When I call the nrfx_pdm_enable_check() the...
Hello,
We are developing wearable devices. 17 sensor terminals send data to the receiver at a frequency of 60hz per second. The data sent by 17 sensors at the same time...
Hello,
I'm interested to know whether the continuous integration and continuous deployment (CICD) is possible on nrf52840 board using Segger Embedded Studio ?
if yes,...
Hi
I currently have a nRF52833 DK which I am using as a transmitter. I also have a custom board with a nRF52811 SoC with an antenna array to act as the receiver for AoA...