I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Should the toplevel declaration bool nrfx_power_irq_enabled; in nrfx_power.c have a `static` qualifier? I'm using openocd/gdb to load a GCC-compiled firmware onto a custom...
Hi,
I think I have properly configured my application to authorize reads on characteristic, yet I do not see an event generated. I get write events, but I don't get read...
Hi,
I am developing a custom board with nRF52811 where I will measure analog signals from op amp on ADC (single ended mode). Signals will be very small, so I need a good...
Hello guys. I'm beginner in Nordic Devices.
I'm working in project that sends Acceleration Data from KX220 sensor over LoRa network or if there is a BLE device connected...
Hi，
I find that nrf52 series can support Bluetooth 5.2 SoC in nordicsemi page, but it still shows Bluetooth 5.1 SoC in Product Spec.
Which one is right ? Is it just that...
In the User Guide for the nRF52840DK on pg 26 is:
8.5 External memory The nRF52840 DK has a 64 Mb external flash memory. The memory is a multi-I/O memory supporting both...
Hi,
I'm working with the USB_CDC_ACM example to communicate with a PC trough COM port. It works well.
Now I would like to use the ISO endpoint feature in order to transfer...
I have a NRF52840 DK, with a pca63511 power profiler kit purchased just a few days ago from Mouser. I am trying to use the power profiler kit with version 2.3.1 of the power...
We are in a need to upgrade the existing Soft Device to higher version from the application firmware. The reason why I am asking this, if it is possible to upgrade then we...
Hi All,
I am Working on nRF52840 and using nRF52840-DK.
Below is my working environment
SDK - nRF5_SDK_16.0.0_98a08e2
IDE - Segger Embedded studio (windows 10 -...
I am using NRF52840 in Mesh (SDK 4.1.0), I am facing this strange issue, one of my node (have client+server both) is got damaged, I replaced this with new NRF52840, then I...
Dear support team,
In the AT command manual, the parameter type are well documented:
But there is no hint or description about parameters in certificate manager. The...
Hi I am using Mesh V 4.0 and Stack V 16.0
I have created the Message Model in Client side and can able to send string from Client to Server on button press.
Now when I...
I am a nRF new user, I try to use JLink-OB (STM32F072C8T6) program nRF52832 module, wire nRF52832 via SWD likes below,
I try to use nRF command Line tools operate nRF52832...
We're trying to make our device automatically recover after a brown-out or brief power loss. I'm hoping to leave a system-state value in a RAM location and check for it on...
