hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hi，
I finally want to integrate BLE and 2.4G in nRF52810.
【1】I am studying Timeslot，i found some articles in DevZone.
There is a mention of micro-ESB ， so what is micro...
Hi, I am currently testing some BLE sample code (the proximity code and hrs code) with the nRF52840 PDK and I am trying to just simply interface the GPIO interrupt example...
1. How should I connect with UART to my board?
2. How to put the device into RX mode as required by RED EN300328?
Test the Radio Test Example application by performing...
Hi,
My problem described below, please share solution or any suggestion how to fix this.
=== Background / Problem ===
I've setup and run MESH serial network, for machine...
If I use RTC and Timer simultaneously, getting fatal error as timer disables RTC. Is there any way by which I can use both application and RTC in my application?
Our device is implemented as BLE peripheral device and based on nRF52832
For saving space in Flash memory we try to downgrade SD version from S132 v 5.0 to S112 v 6.1.0...
Hi,
I am doing one more project in that project I want to do following things:
1) my one BLE giga device module(nrf51822) will act as a master(central) & other AT command...
Hi to all,
i had a problem in measuring coin cell battery level with nrf51822. i am developing a device with nrf51822 that this device will use from a coin cell battery...
I have a product using the nrf24L01+ going through the new CE testing for EN300440 v2.1.1. The lab is asking me how to setup for "receiver blocking" test according to 4.3...
Hi, I'm using nRF52840PDK and SDK 14.2.0. I started from the SAADC example and tried to use NRF_LOG_INFO to print some strings through the UART. I have this:
And...
Hi,
I am following the directions here using Keil:
http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v14.1.0%2Fnrf52810_user_guide.html
...
Hello,
I'm using mesh 2.0.1 to test message sending between 2 nRF52840 DK boards.
I'm using a task from FreeRTOS kernel to send messages from the node to the provisionner...
I was hoping someone could clarify what support the nRF52840 has for USB power source detection. Our design uses a 150mAh LiPo battery, with a dedicated PMIC. We have the...
I have a hardware with NRF52832 module and successfully used the example twi-scanner to locate my I2C peripheral. I copied these parts over:
My own code produces this...
