I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
Hello Everyone,
A part of my logic for the module i am developing requires to put the device (nRF52832) in low power mode for xx seconds. Once the timer expires, application...
Hello,
has anybody put two nRF52832 on the same PCB and make them work at the same time, one with BLE and the other with Bluetooth Mesh?
Or one nRF52832 and one nRF52840...
Hi,
In the multilink example, we are working on 4 links. I have 8 devices.
In the test process, if you connect 4 units first and turn off the 4 units connected at the...
Messages sent from the nRF52832 over serial, using nrf_serial seem to be getting lost periodically as they are received via an implementation on an Android Tablet. We are...
Use 64M Flash to make FAT32 FS, open Writeback mode(NRF_BLOCK_DEV_QSPI_FLAG_CACHE_WRITEBACK), write 1M file "1.txt", "2.txt" in order, use Windows PC to check the prompt ...
Hi,
I need to measure all width of continuous pulses without stopping the measurement. The pulse frequency is about 10kHz. But the frequency and the duty ratio changes dynamically...
Hello everyone,
It seems like a very basic issue but somehow I am unable to resolve it.
I have a characteristic of length 20 bytes. This characteristic is supposed to...
Hi everyone,
I am having problems in getting the twi peripheral to work properly with the accelerometer I am using ( NXP MM8653FC).
I am getting some wierd issues, firstly...
Hi,
I have noticed strange behavior when Android-Image-Transfer-Demo firmware is used (SDK13, softdevice 5.0.0-2.): Demo kit does not startup if powered from the coin battery...
Hello!
I am putting (with a wave generator) a square wave on pin 17 of the microcontroller, and I want that same wave to come out on pin 18.
How do I do that?
Do you have...
I'm using SDK v 12.2 project ble_central/ble_app_uart_c using GCC
After running the project for awhile a stack overflow in the ble_stack_thread() is detected which eventually...
Hi,
I'm modifying the light_switch client example, so that I can use GPIO as input instead of the button. I was able to build the modified example in SES and download it...
I'm attempting Mesh DFU on an Ubuntu 16.04 system. Here are the steps in the quick start guide along with corresponding notes on my setup:
nrfutil keys --gen-key private_key...
