I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello,
I have a project based on nrf51822 and SDK 10/S130. I have read about advertising mode and whitelist, but could not find my answer for my issue anywhere in the zone...
I added a new model to light_switch/server project according this , but how to test it working successfully or not?
I have tried to modify the light_switch/client to accept...
Hi，
When i do as the document say, i download the firmware to the development kit, and then i don't know which pin is the Tx and the Rx. How can i do all the function test...
Hello, I bought nRF51dk (pca10028) a year ago it was working fine last year in Segger Development Studio, now it gives build error "core_cm0.h: No such file or directory"...
Hi guys, me again.
Thanks for all the help before. I was developing me code with the example uart and now would like to control a LED with PWM output.
I have went through...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
I'm using the evaluation board PCA10040 with Segger Embedded Studio. It stopped working well and I get erroneous services even with the supplied examples (ble_app_blinky...
The device is broadcasting as "DfuTarg" and i want it to come out of the bootloader mode back to the application mode. Is there is a command i can issue to Secure DFU Characteristic...
Hi,
I'm modifying files in the NRF5_SDK_14.2 distribution and it is not clear to me which ones are part of the core SoftDevice libraries (and I, therefore, should not change...
(I know it has been asked before, but I thought I'd check in again..)
Has anyone had any success implementing the Dallas one-wire protocol on the NRF51822 - in particular...
Hello,
I imagine this is a pretty common and basic question but I couldn't find anything online.
Since the nRF52xxx chips are single-band 2.4GHz (and possibly sub-GHz...
I'm having trouble writing to a gatt characteristic using the python bindings for pc-ble-driver
Service discovery works fine, I managed to connect to a BLE server and reading...
I have a device that I need to control, that needs 2 different square wave signals of different frequencies (although they may be multiples of each other), one at around 4...
Hi all. I try to run capacitive sensor example on nRF52832 with my hand made capacitive sensor which I made according to this tutorial devzone.nordicsemi.com/.../.I connected...
