Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
I use the nrf52832.
In the beginning,I can download the code and it works well.
And suddenly,Keil told me "No Cortex-M SW Device Found",when I change a new chip it can work...
I use the nrf52832. In the beginning,I can download the code and it works well. And suddenly,Keil told me "No Cortex-M SW Device Found",when I change a new chip it can work...
Hi, i'am working on a custom board on which there is two led drive by a led driver.
The two leds are wiring to be drive by pins P0.14 and P0.15, but unfortunately these...
Hello! I am using a nRF52832 device, along with SDK 12.1.0 and S132 v3.0.0. Data is being sent data through BLE and received on an Android phone.
After some tests I noticed...
I need to have a Central device physically connected (via UART) to a sensor. Data is collected from the sensor and sent to a number of Peripheral devices which use the data...
Take a look at these screenshots. With the trigger enabled, the average current consumption is reported at 13.21uA. With the trigger disabled , the average current consumption...
Dear Nordic,
I want to know if it is possible to send asynchronous data type from a slave node to a master node (master node would be in continuous scanning mode). Reading...
Here is my problem. I want to disable uart when there is no data coming into MCU.
I used IO LotoHi event to enable uart Rx. After finish data receiving, I disable Uart.
...
I've modded the PCA10040 DK for current measurement with an ampere-meter (TTi 1604), using a program which turns an LED on and off every 5 seconds. The measured current stays...
I am using an LG G5 and my co worker let me use a google pixel. I tried using the s132 softdevice along with the BLE UART example code from 12.2.0, I get the device is not...
I'm aware of GATT's Profile, Service and Characteristic.
And also, for GATT_Server, GATT_Client it can be Central or Peripheral. (As I manually set it.)
And also, the...
hi
I am using nRF51822(from waveshare). previously i was able to program my device with nRFgo Studio. But I am facing a problem now. I programmed my device with radio transmitter...
I want to collect data for analysis sent from peripheral(ble_app_uart example), I connected peripheral device to app(nrf connect) and enabled service, now the data is sent...
We want to build a network of many nodes (nrf52 boards) distributed in the apartments, that are connected via BLE over 6lowpan, of course using a border router for communication...
