I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
hello,
i am using nrf52840 with our cutomised board and trying to achieve long range using coded phy and using that long range demo example as base i have sucessfully changed...
I try to send out sensor streaming data to terminal over BLE NUS. Sensor sampling rate is 100Hz and 6 bytes per sample. Is there a best option to do this if I need to send...
We're working on a product that is able to store around 400uC of charge (two 220uF capacitors). There is a constant input of 21 uA minimum coming from a small solar panel...
I'm using AT%XRFTEST=0,1,2,19300,-40,1 to test reception at 1930MHz on the NRF9160 DK with a CW generator, and I don't understand the effect of the -40 parameter. With my...
We are currently working on an energy harvesting solution that powers the nRF52832. The energy harvester is providing energy from indoor solar and at the lowest light level...
I'm kind of confused about the DCDCEN0/1 related functionality and can use some confirmation. If I'm hoping to run everything at 1.8V, it seems I can wire VDD_NRF to 1.8V...
Hello,
In our device, we would like to implement an HID Service for the most simple cases. This part is OK, there are examples for this.
For advanced users, we would like...
Hello,
MCU: nRF52832;
SDK: 15.3;
Project: examples\ble_peripheral\experimental\ble_app_ots
nrf52832 receive data from app, communication by L2CAP, I want to increase...
Hi,
I use library NRF21540.c to config to control NRF21540, to amplifier the radio of nrf52832.
This is my define:
#ifndef NRF21540_USE_GPIO_MANAGEMENT #define NRF21540_USE_GPIO_MANAGEMENT...
Hello!!
I want to implement I2C between nrf52832 and capsense button (CY8CMBR2110-24LQ) and want to put it to sleep mode so that I could get ~2-3uA if there is no activity...
Device: nRF52840
SDK: 16.0.
Softdevice: 6.1.1
Hello,
I'm using Timer 2 peripheral using simple timer driver. It's working fine but I have serious drift/accuracy issue...
I use SDK16 and softdevice S140. I use cdc_acm to simulate a UART port. My data traffic is very heavy. It cause data overwrite and send out many zero. My source code snippet...
Hi,
I have been trying to use nordic nrf52840 USB dongle/ pca 10059 in BLE mode to fetch data published through Bluetooth; however I can find any compilers that support...
I have adapted the example ble_app_gattsin SDK_17. My code is as follows:
However, an error is thrown when setting the scan filter as follows: nrf_ble_scan_filter_set...
Using app_usbd_cdc_acm_write method as blow: I see following output in Putty.
Baudrate is correct (115200) + it decodes first part of the message.
I have no idea why...
