I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
Are there any examples of how to configure the COEX pins between the 9160 and a 52840 such that each will actually use the signals to start/stop their respective radios? The...
I see references to a get (0x8046), set (0x8047), and status (0x8048) messages for Node Identity. Where could I find documentation about these messages? There is no sample...
What is the purpose/functionality of SWO pin (pin 6) on the Debug In port?
I see it connected to P0.18 on PCA10040 and P1.00 on PCA10056, but I’m developing custom board...
Hi,
Though I could able to successfully provision light and switch using nrfMesh Android application with all elements being configured and also could publish/subscribe...
Hi,
Recently, I am studying the blog as the link below:
https://docs.microsoft.com/en-us/windows-hardware/design/component-guidelines/bluetooth-prepairing
We would like...
Hi all,
On the iOS version of the Blinky APP, there is a statement
Created by Mostafa Berg on 01/12/2017. Copyright 2017 Nordic Semiconductor ASA. All rights reserved...
Hi,
I am using pin 27 as SCL and 26 as SDA on my custom board which is working on 1.8V.
There is no activity on SCL pin, while i am getting correct values on SDA pin when...
How can I read the ICCID (Integrated Circuit Card ID) of the SIM-card?
Normally (with competitive modems) I get the CCID by AT+CCID.
The nRF9160 reponds with +CME: 0 ...
Hi, I would like to develop a BLE central node that sends over UART when a button is pressed. I understand the memory is limited on nRF52810, but I think it'll fit. The example...
I am developing on the nRF52832. I just discovered that if my program enables Access Port protection by writing the UICR at runtime, then the program can still be read out...
Hello,
I want to use a third party bluetooth module (based on Nordic SOC) in my application, so far my understanding is that using your softDevice stack I have to implement...
Hi
My Thingy:52 works perfectly OK with Thingy app on my iPhone.
However when I use the Gateway on my iPhone and then nrf cloud I get an unstable connection on the cloud...
Hello Developers,
I have just started playing around with BLE Mesh Zephyr examples on my recently purchased nRF52840-PDK board.
Anyways, I am bit stuck with one fundamental...
Hi,
I've used the nRF51822 in the past to make sensors that connect to a mobile device. Basically it worked just like every other non-mesh BLE device:
1. It advertised...
