Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Looking at the schematic diagram of the ISP-1507-AX Test Board….
www.insightsip.com/.../ISP1507_AX_TB_Schematic.pdf
… I can see that there is the possibility to connect...
Hi
I am using ble_app_uart code from ble_peripheral folder and nrf_connect app to receive/send data.
I have interfaced external sensor with UART pins and receiving data...
Hi I am using UART code from nRF5_SDK_16.0.0_98a08e2\examples\peripheral.
I have checked loop back with default UART pins,which are 5,6,7,8.
Now I want to interface some...
Hello,
I am using a nRF52DK (PCA10056). When I connect the board, the J-link drive opens up, but it does not detect on nRF Go Studio, nor is it flashing any code. I am using...
I'm using the USB CDC ACM example to write a message to a com port. I can receive messages fine except there is one problem. I am receiving the characters one character at...
Hi,
Is it possible to use two LPCOMPs simultaneously?
I would like to use analog channel 6 and 5 and if I register a RESULT Above on channel 6 it should start a software...
Good day to all
I would like to get a little more information about the function:
added in softdevice version 7.0.1.
Starting the radio in connection mode is shown...
Hi,
I'm experiencing some UART issues on nRF52832 where it seems like the peripheral is not correctly reset when doing a soft reset. After a soft reset I expect that the...
Hi,
I am using nrf25840 Dongle as NCP with Linux machine. I have used NCP example hex from " nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac\examples\thread\ncp\usb_bootloader...
How to achieve the lowest power consumption while "sleeping" but still being able to awake from an internal timer ?
For the timer I'm using the Ticker class from mbed.....
Hi,
I am a Embedded System Engineer working in a Medical device company in Ireland. I have a ublox Modem(Nina-B111), which has a nRF5xxx module embedded into it. The modem...
Dear Sir .
I have on my custom board 2 spi , spi1 and spi3.
&spi3 { status = "okay"; compatible = "nordic,nrf-spim"; sck-pin = <31>; mosi-pin = <9>; miso-pin = <30>;...
Hi，
Now I use Nrf52811 to develop a product. I use the 125k long range radio + 4dB mode.
I read through its specifications and found no corresponding...
Hi，
Now I use Nrf52811 to develop a product. I use the 125k long range radio + 4dB mode.
I read through its specifications and found no corresponding...
Hi.
I programmed the firmware in " https://github.com/NordicSemiconductor/pc-ble-driver " share folder to a nrf52840 dongle.
NRF_SD_BLE_API=6
I took the example heart...
