Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
I'm developing a product that use the Nordic UART service over BLE and need something similar to a USB serial port, except with NUS. Is there a Windows 10 driver that works...
Dear Nordic Team,
Thanks for supporting.
Currently i am working in Mesh network. My application is Single Client control 100 Server Individually . Same like this https...
Dear Nordic Team,
Thanks for supporting.
I am new for mesh network concept. I want to control individual device in mesh network (May be more than 10 device). I have tested...
Hi,
I have a project that has a bootloader based on the SDK15.3 secure buttonless DFU example. During pre-production testing, the need for downgrading the app came up. So...
Hi,
I just wanna start off by saying I know there a lot of similar posts to this one here on the dev zone, but my problem with them is that none of them (from what I've...
Hello,
we're just planning to deplay our first border router for bigger in-house installations and wan't to use a USB-Dongle with the nRF52840 as NCP with the Openthread...
Hi All,
We are working on zigbee protocol and wants to replace the existing setup with nRF52840 . We have some below queries need your answers on the same to go ahead on...
Hi
I'm developing an application that is pretended to run on an nrf52810-based custom board, The code is a modification of the blinky example from the SDK 15.0.0, and for...
Hello,
on my previous project i rellay enjoyed the offline documentation of the sdk (SDK14.2).
Since we are using the Thread-SDK now, I haven't found a offline documentation...
I'm using SDK 15.3.2 with SD 132. SES and the 10040 DK.
I'm not clear how NRF_LOG module and the new serial port library is support to work together.
I can easily make...
Hi Nordic!
In our design we see variations in the rev C lot we have received. We are using the VDDH REG0 regulator. Some of our ICs turn ON with no problem. And even when...
When I scan BLE device at nRF UARTv2.0 App in Android4.4, it is appar device name(Ex:Nordic_UART) and 6 byte device address(MAC address?).
I want to include mac address in...
The button is connected to ground directly ,and without external pull up resistor.
I found it consumes too much current when using internal pull up resistor,but when I use...
According to at client demo, LTE-M1 is the default mode in firmware mfw_nrf9160_0.7.0-29.
Modem work mode will be LTE-M1 after every reset even you changed to NB1.
I...
