I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi,
I tried ble_app_uart example by using SES it works fine. Then I tried it by using eclipse with OpenOCD and a STlink V2 on the debug in port I succeeded to flash it....
Hey guys,
With the new SDK15, I find myself looking at dependency problems over and over again. Right now, I am trying to setup a simple A/D conversion using nrfx_adc. Found...
Hi Env: keil uvision 5 and SDK 9 and custome breakoutboard for nRF51822 (PTR5518: no external crystal) and no SD.
I am trying doing the first steps in twi over nRF51822...
I been reading over your entire tutorials, but I have yet to see any tutorials that guides me towards creating an NRF52 project from scratch? Could anyone guide me through...
Hi,
I am transferring my nrf52832 project to nrf52810,and I have deploy the project according to the user guide (Transferring the project to nRF52810 hardware),
when I...
Hello everyone,
I'm developing an application for boards with NRF52832, Softdevice S132 3.00 and SDK 12.3.0.
The network architecture consists of:
one peripheral board...
I'm using my accelerometer's GPIO interrupt to wake up the MPU from PowerOFF mode and it works great. Now, I'm trying to use the same interrupts to wake it up from Sleep mode...
Hi,
I have migrated from SDK14.1 to SDK15.
One thing is embarrassing me.
I would like to modify the scan data as above, I do not know where I can fix it.
phy...
Hi,
I am using mbedos for a NRF42832 and am currently in the situation that I have to profile my code with gprof. Here comes the issue: the Nordic SDK uses explicit assembler...
this picture is from infocenter.nordicsemi.com/index.jsp
and this picture is from 《S132_SDS_v5.0.pdf》
in first picture the application base is 0x00020000 , in...
I've been instrumenting my Nordic app with RTT logging, which has been working great up until now. I use the deferred mode and use nrf_log_push() to queue all dynamic strings...
For the connection event collision, I have some doubts, I hope to get help in devzone
http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.s132.sds...
Hi, everyone,
We develop BLE project including DFU bootloader.
But to use the standard bootloader "as is" it is not possible for us. Due to this problem we must make some...
On Apple platforms, It's pretty easy to end up in a situation where there is bonding information on the Nordic but that information has been deleted from the host. All you...
Hello,
I am using sd_power_system_off(); sfunction to put the MCU in sleep mode. I have to wake up events. One is NFC and the other is GPIO. Both wake up functions works...
