Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
in sample ,prj.conf had configure ble device name using below define :
CONFIG_BT_DEVICE_NAME="Nordic_UART_Service" ,
in hci_core.c function bt_enable() use set_bt_name...
Hi Nordic,
In this question: https://devzone.nordicsemi.com/f/nordic-q-a/56529/how-to-check-or-read-the-list-of-bonded-device-from-nrf52832 It was discussed to update...
Is it possible to use both Zigbee & BLE MESH at same time?
Actually we are planning to use NRF52840 for our next project. In which BLE MESH will be used for BLE mesh device...
Hello,
I am using NCS v1.5.0 and my application runs in non-secure mode, and uses a custom SPM. Initially all build and ran correctly, and the SPM fit in a 32 KB partition...
Hi Dev team,
I am running an application using Thingy91 along with MQTT.
I am having a simple logic of storing data for a while and then sending it out through MQTT. For...
Hello,
I've been testing 802.15.4 single PHY (no softdevice) and analyzing packets on a TI CC2531, just to check interoperability. Things seem to work well when the packet...
Hello Everyone.
I am a newbie in NRF52840 development. I have one NRF52840 device as a central device and many peripherals are getting connected to it (Max 6). Lets say...
I am currently using the 17.0.2 SDK to develop some code on the nrf52832 which involves streaming data via SPI to an external flash. I need to stream this data at a ~50KHz...
hello, I have a question need you help.
SDK:nRF5_SDK_14.2.0
MCU:nRF52810
My product is used as a central.
When the voltage of the battery supplying the product is...
I am trying to develop an application using ANT on the 52805, I have purchased the nRF52 DK as this was the recommended development kit for this device but there seems no...
I have a design that uses the NRF52810 as well as NRF9160.
For safety reasons, it must have a fuse that is about 1 ohm into the system. I'm seeing an issue after an input...
Hi, Nordic.
Our customer employs nRF51802 in their product.
They use BLE and 2.4GHz proprietary at the same time. They want to know the switch speed between the two protocol...
Howdy DevZone! I'm brand new to BLE, and have some beginner questions on the best way to architect a project for ultra-low power consumption.
Here's what I want to make...
