Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi,
I working on a BLE app with 2 custom services.
When I try to expand a characteristic I get a spinning indicator below the characteristic and after a while I get...
in nrf5 sdk 17.0.2 example\ble_app_hids_mouse , hid map
correct is 0x95, 0x05, // Report Count (5) is five ! is five
Forgive me for just reading the comments at first...
Hello, I'm using nrf52832 and i need 2 UART instances in parallel. I get an error when I set the second UART.
Do you have an example using 2 UART instances in parallel?
Hello,
i am new to the topic and am looking for tutorials, additionally to the nordic examples and this community.
I found the following website:
https://embeddedcentric...
Hi,
When a board is connected to debugger, It works well for 2 hours.
But when it is detached debugger, It looks like stuck to POWER_CLOCK_IRQn after 4~6 min after power...
Hello,
I'm trying to make a one-shot MQTT publisher and I'm able to get 22 messages published but every time I try to publish the 23rd the code hangs in mqtt_transport_write...
I'm not able to get a response using the new CONEVAL AT command. I'm using firmware v 1.3.0 and a recent B1 variant nRF9160. Response is always ENOEXEC. I have tried before...
Hello,
In my project, nrf_drv_gpiote_in_init is used 3 times.
battery measure
sleep trigger by motion sensor
wake-up trigger by motion sensor
After 3rd call...
HI
I am trying to interface ads1231 with nrf5340. Regards I need to know about Gpio read. Because ADS1231 gives digital output. I don't know how to read actually. Kindly...
What is the purpose of the ble_advdata_encode() method?
I see it has been used in the beacon example, but some other examples don't use it.
In both case, the advertising...
Hi, all..
An error occurs as soon as it connect and disconnect through advertising. Timer interrupt is currently running on the main function..
and then I found error...
OS: Mac
I installed nrf v1.2.0 and Segger Embedded Studio v4.42a. I can't open project and it causes error.
I can open projects with this config on SES v4.42a and...
Hello,
I installed Segger Embedded Studio v 5.34a following the online instructions AND the Getting Started Assistant instructions for a Mac. I then tried to import a project...
Hello everybody,
I'm trying to develop mesh network with zephyr, but the problem is that logs are not displayed in SES debug terminal. In autoconf.h file I can see that...
Hi,
I have been following this post and did all the steps instructed by , but I failed to receive a response in Tera Term in the end. I have also tried changing the hostname...
