I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi Dev team,
I am working on a Thingy91 device, and I am sending data out through MQTT.
I need a functionality to send some commands to do assigned tasks from the MQTT...
Hello everyone,
I am simply looking for some clarification on how to correctly handle button presses on the nrf52840 DK, as there seems to be multiple ways to go about it...
Hi,
I'm trying to build a working example of an aplication that uses the ANT+ softdevice (either s210 or s212). I already found out that the PCA10028 and PCA10031 (my board...
Hello,
This is more of a C question and I am new to Embedded C programming, I have this question.
I want to know how to access the flash memory without fds or fstorage...
Can we use beacon as a broadcaster and observer in thingy 52? Please suggest the way how to enable led indication using the distance generated from RSSI value and the data...
Hello,
When I use the " west update" command to update ncs1.4.99-dev to ncs 1.5.0, the following error occurred. How can this situation be solved?
Thanks.
BR,...
Hi, i am electronics engineering student and i have a project with nRF52832.
I want to design NFC antenna on PCB but i have not a experience and information about this topic...
I use custom board nrf5283 ..
Getting the following error while trying to flash
ERROR: JLinkARM DLL reported an error. Try again. If error condition ERROR: persists, run...
SDK: 4.1.0
CHIP: 52840
old question
my sleepy zed lost connection to the coordinator after refreshing key of the coordinator.
1) how can I manipulate refresh...
Hi All,
Is there any proper method for updating the firmware via serial port of nRF52840. The same process as arduino or esp32. Can we invoke the updation process with a...
Hi Nordic Team,
Summary: Please guide to open and build simple example nRF5340 project using Segger IDE on Windows 10
Details:
We tried to have Segger IDE setup for...
I am trying to compile a sample application for the Board nRF5240 . While i install the nRF Connect SDK for ncs v1.5.0 through Toolchain Manager 0.9.1 , I get the error as...
HI,
Is it in anyway possible to change the maximum gazelle payload size to 64byte instead of 32byte, I need more data when I send data return to the device.
Hi.
I am working on the MSC, and starting with the usbd_msc demo. The windows explorer will show a disk named "USB Drive" if connect to the PC.
I would like to change...
