Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi Nordic,
We're developing a product based on the nRF52810 and got the following question:
We were wondering if we can recover a board in the worst-case scenario where...
Dear all, My team want to develop a innovative product. I am following this tutorial ( www.youtube.com/watch to enable the CMSIS Configuration Wizard in Segger Embedded Studio...
I am working with SDK15.3.0 and a PCA10040 with S132. I have two questions relating to the BLE addresses as seen by the PCA10040 and by nRF Connect.
Q1 - What is the relationship...
Modem firmware version 1.0.0
Segger version v4.18
nrf tag v1.0.0
Often when I try to flash a new build of an application and try to flash an application through Targert...
Dear Team,
I want to integrate an nRF chip into my Project. I will use a ready made module from Laird, the BL652-Sx.
For Debugging I want use the nRF52 DK and connect...
Hi all,
we would like to add usb-cdc support for our nrf mesh project. I have tried merging an usbd example project into our application but without success so far. I am...
When I try parse string on nrf52832 with SEGGER Embedded Studio for ARM 4.16, I have a problem about "sscanf" :
Here is code:
It should output:
Num: 12
Num:...
Hello to all! I use the sleep mode PWRDWN = 0x04 and periodically wake up at WDT.With that, I see needles for the current consumption in the circuit to wake up the circuit...
I measured the output power over all the channel, see graphics below. It is not much, but i still would like to know why the output power drifts over frequency. Is this by...
Hello,
I have two nRF52832 (BL652) modules setup and connected through an RF cable. I am feeding the peripheral radio (2x) 174 byte packets every 5 ms. On the central, I...
Hi,
nRF9160 mqtt works with ipv4 by using "ncs\nrf\samples\nrf9160\mqtt_simple" application.
Now NB-IOT network which we are using is faced out the IPv4 and moved to IPv6...
So we have a great set of 52832-based set of products in the field that negotiate, agree to, and support MTUs larger than 23 bytes. Nordic's is incidentally one of the least...
Hello everyone!
As far as I've read in the manual, Power Monitor allows to export measurement data to file and use the for further processing. I'm using Power Monitor v2...
Hello,
I am using ublox B201 for my project which is based on nRF52832 SoC & with use of SDK 12.2.0.
So i need to know which IDE supports nRF5 SDK 12.2.0 ?
As segger...
