Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
When I try to update the firmware by sending 20 bytes at a time, it fails after around 1.25 minutes consistently.
1. Is it because nrf52 cannot hold the ble connection...
We are starting to get ready for production and will have 24 board on each panel. It would be great to be able to "chain" 4 to 6 nRF52840's together using the multi-drop protocol...
Hi everyone,
I'm currently developing a potential product where I wanted to use the nRF24L01/+ to send out BLE advertisement packets for a mobile app to receive and decode...
We are using the iOS DFU SDK https://github.com/NordicSemiconductor/IOS-Pods-DFU-Library to update a device that is built against the nRF5 SDK 14.2.0. The problem is that...
Hi,
I implemented my application top of the mess 3.0, mesh is working fine able to hop the messages to the gateway via relays(nodes)
Issue with UART : -
here nrf52840...
SDK version: nRF5_SDK_15.3.0
Platform: nRF52840 DK
---
Add FreeRTOS into serial example( nRF5_SDK_15.3.0_59ac345\examples\peripheral\serial )
and I copy task of blinky_freertos...
Hi,
I want to read 4 - ADC input channels (12-bit or 14-bit) from Bluefruit nRF52832 feather using sketch code. Can you point a sample code to do this?
I could read default...
Hi,
I am currently trying to set up the HTTP Application Update Sample and unfortunately it keeps stopping at the "downloading" state. Code is exactly the same from the...
Hi,
I´m using nrf52840 with softdevice S132 and set ble_gattc_conn_cfg_t::write_cmd_tx_queue_size to larger than 1. I´m count number of queued writes by increasing a counter...
I am currently developing with nrf52832 sdk14.2. I found in the test that after opening the hid service, the connection parameters will become the following parameters after...
I encountered a scenario where I call sd_ble_gap_connect() and get an event BLE_GAP_EVT_TIMEOUT with source BLE_GAP_TIMEOUT_SRC_CONN . This is followed immediately by an event...
Hi, i have written code in android, where i am using threads to connect to 832 ble over insecure RFComm socket..
Am not pairing with 832 in my app and am directly trying...
Hi I am implementing a buttonless_DFU function right now. I decided to do Buttonless on my project's PCB Board because it is no longer an environment where I can add switches...
My setup is as follows:
nRF5 SDK 13.1 with s132 5.1.0
nRF52832_AA
Keil 5.25pre
I use RTC1 counter for timestamping along with app_timer timers. My get_timestamp() function...
I am trying to send lots of data through radio (basing on old micro esb project from github, but heavily modified).
I need to keep radio IDLE (not DISABLED) when not transmitting...
