I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
Good day.
I`m very new to nordic chips.
I`m try to use NRF52832 as TWI master with OLED display based on SSD1306 with I2C.
And got this.
Yellow is SCL, Blue...
Hi,
I am trying to use the FDS for saving some variables and displaying them again later. I have downloaded the NRF52-fds-master sample code posted on github. However,...
i am working with mpu xx example given in nordic website. it seems code is working fine i.e. compiling and dumping into nrf52 DK, But not showing any output values.
i was...
I am using an Nrf51822 for a project. I looked in the datasheet and it said that there is a built in WDT for the chip. It also says that clocks can't be used while in systems...
I want to use in my project tft 1.8 display with st7735 controller. I'd like to use some based code but can find nothing except on infocenter nordic
As I understand there...
Hi,
I am writing a boot loader which does not need to use the soft device as the image is being transferred over an SPI interface.
I have merged the softdevice and my...
Hi
I suppose that Multiple connection to centrals is available from BT4.1.
Is it possible to realize bu S110?
If it is so, which version is available the specification...
Hello, I made some boards on nrf52832 and I was testing the PCB.
The test program is ..\nRF5_SDK_12.0.0_12f24da\examples\ble_peripheral\ble_app_hrs.
(I have downloaded...
Hello! Just got a few NRF51822's.. looking to just brodcast a few basic URL's.. if someone can point me in the right direction or maybe let me know where I can hire someone...
I work with ble_app_uart example and want to move uart init and event handler into separate file( e.g uart.c).
I just copy uart_init, uart_event_handler functions with some...
I am writing code that runs on a NRF51822 (to be less specific it runs on a Red Bear Lab BLE Nano). The board has a 32.768khz crystal on it that I want to use to wake up the...
Now I am sending data at 250 ms.
I'd like to send data at 80 ms.
Is this possible?
also,how much can it extend the advertisement interval to the maximum?
thank you in...
i am working with eclipse to program the ble_app_hrs but it is getting error "No rule to make target _build/app_trace.o', needed by nrf52832_xxaa_s132'. Stop" when it builds...
Hi,
In the newer versions of NRF 5 SDK (sdk10 vs sdk12), does the softdevice takes more RAM?
I am using nrf51822 (qfaa) and sdk 12.3. with softdevice s130_2.0.0.1....
I can't get my PCA10040 board to send serial data when connected to a FTDI USB dongle.
When the FTDI dongle is disconnected, and I connect my logic analyzer to the tx and...
