Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
Hi,
I have a project which has been working fine but since adding some date/time functionality, when I enable MCU_BOOT, I get linker errors that I can't seem to get to the...
Hi all,
I'm developing a multilink system with 52840 dongle as central and 8 52832 devices as peripherals, which is similar to previous project in thread part I & Part II...
Hello,
As mentioned in the title, I am trying to use 4 pairs of I2C on nRF5340. Each of the four I2C pairs will be connected to a TCA9548A (I2C MUX), but that is not important...
I want to try out remote mesh provisioning.
I have added a mesh device with Remote Provisioning Server model to my mesh network with nRF Mesh app as the provisioner.
But...
Hello,
I've been trying to setup the nRF connect & power profiler on some of my co-worker, but downloading the pc-nrfconnect addon was not possible via nRF connect, so I...
i used my j-link to flash to my thingy91 nrf52 and nrf91.
now i want to flash a new program using the usb, but nrf programmer doesnt recognize a device when i use a USB...
Hi, I'm trying to send 64-byte reports for INPUT and OUTPUT: 1 byte for report ID and 63 bytes of data. However, the HID service code doesn't seem to handle incoming OUTPUT...
Getting error: board.h and other header no such file or directory. with nRF5_SDK_15.0.0_a53641a and nrf5sdkformeshv500src in the same path.
What could it be?
The evaluation...
I'm writing my own lightweight bootloader for nRF5340 (which may or may not turn out to be a good idea). I have something similar that I'm using successfully on nRF52832 based...
When I use the command to read the software version, the message read by the Raspberry Pi does not appear " SoftwareVersion ".
Please confirm the attached LOG message
Hello,
I have a question about performing OTA via BLE (SMP) and using BLE mesh. Is it possible to perform OTA via BLE to ZigBee network and vice versa.
Since BLE is supported...
Hello,
I'm encountering issues while trying to install and update the nRF Connect SDK (NCS) environment on my macOS system.
NCS versions attempted: 2.2.0, 2.6.1
...
I am using nrf52840 to test the `periodic_adv_rsp` sample application using ncs. I had this use case where I would like to configure data in a subevent based on responses...
Hi Nordic community,
I'm starting this course as I'd like to start with Nordic.
I can't continue (better to say, start) the course as the instructions are different from...
Hello, I have an eval board of " nPM1100-EK -> PCA10123 0.8.0 " battery of li-po 3.7v 600mah battery termination voltage is 4.2V The above eval board works fine & the battery...
