I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
SDK 16, S132 V7.0.1, NRF52832, custom device, custom firmware.
Hello,
I want to keep beaconing advertisement (not connectable advertisement) while the BLE is connected...
Hi,
I have a question concerning the SIG qualification. We use the ublox BMD-350 (nrf52832) that is qualified as a component (QDID 101018). I don't really understand the...
Hello,
We are using nRF52840 chip with S140 with ble_app_blinky example.
I was merging Serial DFU bootloader, SoftDevice, application and BLE settings with below commands...
Hi,
I am trying to implement DALI-104 (IEC-62386:104:2019) on top of Thread protocol.
I am using Thread: CoAP Client and Thread: CoAP Server and want to configure these...
Hi,
I wrote my codes to toggle notification on and off using a button using nRF25840-DK and sdk v15. The task looked a simple one; however, I hit some issues such as error...
Hello Nordic Team,
We are working on a project based on nrf51822, we have a problem regarding the incorrect ADC values while waking up the microcontroller from System...
Hello,
I'm developing a custom asset tracker board. My software is currently a very lightly modifed asset tracker v1; my provider currently only support NB-IoT, firmware...
After that one of Zephyr's configuration files was modified (CMakeLists.txt, *.overlay, prj.conf).
How the SES project can be updated in additional to option "Open nRF Connect...
I'm trying to use the board support package (BSP) through a keil software pack, starting from the dfu_dual_bank_ble_s110_pca10028 example. I thought it would be more or less...
Hello, I have installed (multiple times) the nRF connect SDK via the manual installation guide but I still seem to be unable to open any project.
I have tried on MacOS and...
Hello,
We are currently using SDK v17.0.2 with NRF52840, driving a display with SPIM3. We are able to successfully communicate with our display and command it to render...
Hello. I'm designing a board with NRF52832 connected to SGTL5000 via I2S. I'm planning to use the driver found in the Nordic Playground here...
https://github.com/NordicPlayground...
Hello,
Before going into detail, the question is: Is there is any chance that NAND flash will be supported (via QSPI or SPI) by the nRF5 sdk in the future ?
My question...
I made all of the functions using nrf52832, s132. Now I want to reduce the current consumption.
So, I tried changing the slave latency. It was confirmed that the current...
