Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
i use nrf 52832 for scan BLE adv, sdk 12.3 ,
for reduce the missing scan signal, I use three ble_central BLE to scan, so i want set one ble_central to scan one fixed single...
I'm using the Serial_LTE_Modem application (nrf source version, zephyr v2.4.0-ncs1, mcuboot v1.6.99-ncs1, mcumgr v0.1.0-ncs1 ) with version 1.2.3 of the modem firmware. I...
Hi Nordic Leaders,
I need to complete nRF5340 based C++ Software simple solution for ONLY Data Transmit, Receive and Data Store on Flash for our Tier1 Medical client by...
I'm working with an nRF52840-MDK from MakerDiary in the nRF SDK for Thread and Zigbee. I would like to power on an LED when the chip is powered on. Here's a snippet of my...
Hi Guys，
According to the MESH document, there are two ways of node provision: PB-ADV and PB-GATT (smart phone) . A provisioner provides the unprovisioned device with provisioning...
This result is happening very seldomly but I can see it on the logs. First I get a 0x0000 result and then a 0x000A result in the fds event hanlder after calling the fds_record_update...
Hi,
Why does your web page https://infocenter.nordicsemi.com/index.jsp?topic=/struct_nrftools/struct/nrftools_nrfconnect.html&cp=8_3 titled
nRF Sniffer for Bluetooth LE...
I think this is a very simple answer but I can't find out where the file is to edit for this.
From the nRF Connect v3.6.1 - Toolchain Manager there is a drop down and "Open...
Hi everybody,
I have been reading the serialization documentation ( infocenter.nordicsemi.com/index.jsp and I am not very clear about some points.
What is it for and...
Dear all:
I want to implement FreeRTOS using NRFX, I checked the example and discovered that it uses the nrf_drv_clock... and thus it becomes a spaghetti with this legacy...
Hi,
I am working on a project that involves 2 nrf52840 DKs. One device will be running a ble application while the other device will be lookin, fetching and programming...
In SDK 1.4 we combined the udp and GPS examples and the result is unstable.
I think this could be because once enabled by RRC mode == Idle, GPS keeps going forever.
After...
Hi,
I have an issue with using the %XRFTEST command for TX testing on the LTE-M network. My setup consists of the nRF9160 DK (PCA10090) with the MFW 1.2.3 and a 1NCE SIM...
hello,
i am using two customised nrf52840 boards to get maximum range between the boards using this example https://github.com/NordicPlayground/nRF52-ble-long-range-demo...
