Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
in application design , this pin is not connected to VDD , but application board works well ,
application's power range is 2.2V - 3.3V (AAA batteries), max current consumption...
I'm attempting to troubleshoot why my HM18 doesn't connect to the ESP32 over BLE. I'm now deep in the rabbit hole that is BLE sniffing so now I'm trying to determine if the...
Hello,
I did a side by side comparison of the latest nrfutil v6.0.0a0 vs v5.2. It looks like v6.0.0a0 is much slower.
Looking at the log from the target device, it looks...
Hi,
I have installed Embedded Studio for ARM v4.22. However, the studio crashes when I select 'Activate Your Free License'. Reinstalling does not help, and neither a different...
Hi,
In order to read values from TH02 sensor(Address: 0x40) I first need to give a command i.e. write 0x01(for temperature) and 0x11(for RH) resp into internal CONFIG register...
What is the least expensive J-Link Model is required to program a nRF52840 on a custom commercial PCB?
I see that it is a ARM Cortex-M4 core, but I want to double-check...
Hi
Im using nRF52832-QAAB0. SDK 15.3. Softdevice is running.
With debugger connected, calling nrf_pwr_mgmt_shutdown(NRF_PWR_MGMT_SHUTDOWN_STAY_IN_SYSOFF) will assert in...
Hi everyone. Do you know any example of some over the air FW upgrade of nrf52832 chip via ESB protocol. As I understand it should be some combination of bootloader with DFU...
Hello,
We have selected nRF solution for our next product line and currently evaluating the software/SDK setup for that.
We are testing following SDKs:
nRF5_SDK_15.2...
in SDK 15.3.0, no eddystone lock event (NRF_BLE_ES_EVT_LOCK) is triggered after the unlock key was changed.
according the eddystone configuration specs:
A single byte...
I use example ble_app_uart, SoftDevice sdk 6.2.1, when receive data from bluetooth, then drive IO pin 18 to send infrared wave.
received data is Infrared raw formate, which...
Hi,
Our product uses Fanstel BM832 chip. As per https://www.bluetooth.com/develop-with-bluetooth/qualification-listing/qualification-listing-fees/ , should we opt for Innovation...
Hi
I am using TH02 for temp and RH measurement
I understand I must use TWI provided in SDK. However, I a working have c++ library(Wire.h) for I2C that I used with Arduino...
Dear All
I am right now working on BLE development with nRF52840DK. I checked a number of materials, including official specification from Bluetooth SIG, but none of them...
Hi,
I need to read a couple of external inputs - think buttons (although it's actually a sensor with relay output). It's for a prototype obviously.
I need to connect at...
