Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
Hi:
I just got an nRF52832 development board, I have ran the tutorials using Eclipse and I was able to run the blinky example.
I am now trying to get a BLE application...
Hello,
As far as I understand previous versions of DFU BLE bootloader implemented a timeout so if DFU is not being used and an app is present it will run after a few time...
Hi,
I want to OTA firmware upgrade of STM32 (External MCU) using nRF51 through Android App on BLE. STM32 and nRF51 communicate on UART.
Please any one suggests how to...
My project based on nRF52832 and SDK is 12.2. I need to support alert notification(service UUID 0x1811) client profile for mobile device, I just build and download the nordic...
I've been seeing occasional failures of my application which I now believe are due to a bug / design flaw in the app_timer library module.
The problem is due to a race...
Hi :
I have problems ,for gpiote interrupt hanlder can be hanged up by softdevice. In normal use ,I should pull up sck pin of my private ADC chip for less than 10us and then...
Hi,
I'm using the SDK 12.2 with the sd 132 3.1.0, and actually I'm trying to send two separate advertisements wich I'm swapping every "radio notification event", but I...
I am working on modifying the ant+ sdm example to hack my treadmill. Got the example running and talking to my Garmin watch and the display simulator. All of that seems straight...
This problem didn't appear every time when I upgrade firmware. If I restart my app again, sometime the SDK can works well.
Anyone can help? I'm use SDK in Android, Legacy...
Hi,
I am using nRF51-DK and nRF5_SDK_12.2.0_f012efa. I have programmed Proximity example from the SDK to the Development Kit and was able to successfully program the DK...
I have a function with a return value in the time slot, after the function is done inside the time slot signal callback function, I want to use the event callback function...
Hi
We'd like to set the pairing timeout when using the function sd_ble_gap_authenticate(conn_handle, p_sec_params) . The reason for this is that we are setting the connection...
(/attachment/182b723590b3c447267d5aed62b5405f)hi, i want to work on PWM to controll the vibration coin frequency for certain time period and also to change RGB values of LEDs...
Hi!
I'm reading the PS for nRF52832 and I can't find a clear answer on the following question.
If I set up a GPIO channel with pull-up/pull-down in the PIN_CNF[n] register...
